Bedienungsanleitung Elkron IR600FC-N (Seite 7 von 18) (Deutsch, Englisch, Französisch, Italienisch)

741401

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

DS80TC2S-001 7

Features

Image acquisition

Once the alarm system is activated, three 640x480 pixel images or six 320x240 pixel images are acquired when motion is detected.

The detector can also be used to acquire images manually using a remote control (app, portal or local control panel).

Initialisation period

The detector is initialised for 40 seconds when the control unit enters activation mode or when the detector is set to Test. The

detector does not manage intrusions or movements. If the battery of the detector is flat or if the tamper switch is open, the blue LED

lights up during the initialisation period.

Sleep Time

When the JP2 is set to Off, the detector will respect a “sleep time” of approximately 1 minute to save energy. If the system is active,

the detector will not repeat the transmission for 1 minute if motion is detected after the transmission. Any motion detected during

this time will reset the sleep time (taking back to 1 minute). Consequently, continuous motion in front of the detector will not

discharge the battery.

Battery and flat battery detection

The detector is powered by three CR123A 3.0 V lithium batteries.

The detector is provided with the flat battery detection function.. When the battery voltage is flat, the detector transmits the flat

battery signal to the control unit. If a flat battery condition is detected, the blue LED lights up for two seconds.

While replacing the batteries, after having removed the flat batteries, press the tamper switch or the function button twice to

discharge the device completely before inserting the new batteries.

<NOTE>

During replacement, pay particular attention not to damage the contacts in the battery holder compartment.

Tamper protection

The detector is protected by a tamper switch which is compressed (closed) when the detector is fixed to the wall or the corner

bracket is applied. When the tamper switch is opened the detector sends a tamper open signal to the control unit to inform the

user. If a motion is detected while the tamper switch is open, the blue LED lights up for two seconds.



The detector does not detect the tamper switch state for five minutes after the battery is inserted.



If the tamper switch is operated in the five minutes during which there is no detection, the detector will immediately transmit

a tamper signal to the control unit.



When the tamper switch is compressed, the resetting of the default settings of the detector (see below) is

deactivated.

Supervision

The detector regularly transmits a supervision signal to indicate the condition according to the user's setting. The user may also

press the function button once to manually transmit the supervision signal.

Test mode



The Test mode is used to control the detection coverage of the device not the communication range with the control unit.



To access Test mode: hold the function button pressed for five seconds. The blue LED will light up and stay on for

approximately 30 seconds after having released the button. Test mode, which lasts for 3 minutes, will start after this time.



The detector will start initialisation during the first 30 seconds. The detector does not manage intrusions or movements

during this time.



Motion detection in front of the detector can be checked at the end of the initialisation period. The blue LED lights up for

two seconds after detection.

<NOTE>

Check that the "Rest Time" function is not enabled before entering Test mode.

Setup

Guidelines



- Check that the control unit is working before inserting the batteries in the device.



- Check that the control unit is within the working range while the device is in use.



- A device may be removed from the system only after having removed the battery. This prevents unnecessary battery

consumption.

Connecting to the system

The detector must be learnt by the control unit to transmit the signal if motion is detected. Proceed as follows to perform the device

learning procedure.

The detector may be learnt by the control unit only within three minutes from switch-on.

1. Remove the battery compartment lid and insert the three CR123A batteries (included).

2. Make sure that the tamper switch is open (released).

3. Make sure that the learn function has been activated on the control unit. Within three minutes from switch-on, hold

the function button pressed for 10 seconds and then release it when the blue LED and the illuminator blink once.

4. After having been leant by the control unit, the detector is automatically recorded in the system. Check the control unit

to check that the learning and registration procedure were performed correctly.

5. Once learnt by the control unit, if the detector connection is lost, the LED will blink once every 20 minutes to signal the

fault.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron IR600FC-N Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elkron IR600FC-N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info