Bedienungsanleitung Elkron IT500WEB (Seite 14 von 40) (Deutsch, Englisch, Französisch, Italienisch)

741402

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

14/40

STEP 4 - Configuring cameras (Skip if there are no cameras)

WARNING! Even if TC19 (80TC1U00133) and TC20 (80TC1V00133) cameras are

branded Elkron, they must be configured as “OTHER” cameras. For configuration, refer

to “STEP 5”.

1. Use the CDRom included in the camera package and insert it in your PC slot, then install the IP

Discovery software. Launch the application that will search for and display the cameras available

in the wired LAN (or WI-FI) network. Select and click on an IP address from the displayed list of

cameras, then press the CONNECT button. After establishing a connection with a camera, you

will be prompted to type a user name and password for that camera (factory username: admin,

Psw: admin). Then, the camera image will be displayed on the screen.

2. Together with the image, a menu will be shown from which to select the "Settings"  "Network"

 "General" items and then set the  Static IP  Netmask  Gateway and (if they are known)

the network DNS, too. Save and exit the menu.

3. Enable the technical code on the control panel (factory setting 000000), and from the Master

Code, the "REMOTE ACCESS" option.

4. From your PC close down IP Discovery and open the application Hi-connect.

5. Select Manage  Systems.

6. On the list of systems, select the concerned system and then  Open to Manage.

7. Select the “Web Server” TAB.

8. Check that the present connection mode is the required one (e.g. LAN (IT500WEB Local) –

192.168.xxx.xxx:xxxx).

9. Select “Connect”.

10. After a connection is established, the green dot in the dialogue box will illuminate: select from the

displayed menu the item  Cameras, by ticking the fields in the Hi-connect window, the 

camera NUMBER,  TYPE (Elkron/other) and  ADDRESS (static IP or dynamic DHCP). Save

your settings by clicking the icon shaped like a "floppy disk".

11. The factory physical IP address of the cameras is 192.168.1.200.

12. Repeat the same setting procedure for all the other cameras concerned and/or present by setting

a different or suitable IP address.

13. After completing the procedure, save by clicking the "floppy disk" icon and then "TRANSFER".

14. At this point, the WEB server board will restart automatically reading "Restarting. Please wait".

15. Wait approximately 6 minutes for the reboot; at the end, the following confirmation message will

appear: Procedure correctly completed  press  OK.

Re-connecting will then be performed automatically; log out and close down Hi-connect.

16. Access the browser of your PC for connection to the Web server, open the web page, log in

(with the credentials of the Web Server board) and click on the item  Video surveillance 

Video cameras  to check image viewing via the cameras connected to the system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron IT500WEB Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info