741402
15
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
15/40
STEP 5 - OTHERcamera configuration (non-Elkron cameras)
WARNING! To install non-Elkron (OTHER) cameras, check that they can reply to a
HTTP request providing a snapshot in JPEG format with maximum resolution 1280x720.
Note: Use of Static IPis recommended.
For example, URMET BOOST cameras can be used (models: 1093/139M2 1093/141M2
1093/142M2 1093/176M2 1093/177M2 1093/178M2).
The following instructions are valid also for Elkron TC19 (80TC1U00133) and TC20 (80TC1V00133)
cameras.
Proceed as follows, if these cameras are used:
WARNING! Check that the camera firmware is 1.1.9 or higher. If the camera firmware
version is lower, contact Customer Service (mail: stac@elkron.it and ask for an update).
WARNING! Check that the Web Server firmware is 2.0 or higher. If the Web Server
firmware is lower, download the update from the Elkron website.
WARNING! Make sure you have the latest versions of IP-Connect (V1.10 or higher) or Hi-
Connect (V3.70 or higher). If the versions are not up-to-date, download the update from
the Elkron website.
1. Connect the LAN cable to the camera directly to the PC.
2. Prepare and set up the following IP address and network parameters on the PC:
IP:192.168.1.10 -- Subnet Mask: 255.255.255.0
Note: The default IP address of the camera is 192.168.1.168
3. Using Internet Explorer access the camera programming
(192.168.1.168, user name: admin, password: admin)
4. Set IP address, Subnet Mask and Gateway (to select the default IP address, Subnet Mask
and Gateway of the camera, connect to the router of your network and check the IP
address mode).
5. Select main stream resolution to 1280 x 720, save and quit.
6. Connect the camera to your network.
7. Reset the PC network parameters for operation on your network.
8. Start Hi-Connect or IP-Connect.
9. Configure the camera (see Step 4)
10. Set the following programming parameters:
IP address
User Name and Password
In “Full Image URL” enter the following string:
“/Snapshot/1/RemoteImageCapture?ImageFormat=2”
In “Image URL” enter the following string:
“/Snapshot/1/RemoteImageCapture?ImageFormat=2”
Save and transfer the programming to the Web Server.
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Elkron IT500WEB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info