Bedienungsanleitung Elkron MP110 (Seite 19 von 20) (Englisch)

741484

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

(((ELKRON)))

MP110 USER MANUAL

(((ELKRON)))

MP110 USER MANUAL

2.Access Codes

• The unit can be programmed so as to enable User 2 (e.g., service

personnel, custodian, porter , telemonitoring, private vigilance, etc)

to have his own secret access code which allows him to arm/disarm

the unit without performing other operations.

• The unit identifies up to a maximum of 8 different assigned codes and

as many users:

• After entering a correct code that is enabled, the unit’s buzzer beeps

twice, or it beeps once at length to indicate an error. The Master user’s

code is always enabled; the other codes must instead be enabled (refer

to par. “Code Enabling”).

• If the engineer’s code is enabled, it remains enabled until the Master

user’s code is again entered to partially or totally arm the system, or

until the first arming by electronic key-

• Once armed, every re-entry/EXCLUDED display procedure triggers a

1-minute delay (that is reset each time the key is pressed). If a delay

time-out occurs, the procedure is exited automatically without saving

the changes made.

• Each time the key is pressed on the KP100 keypad (segmented

display), while entering the secret code, a segment of the display lights

up to display the digits (entered) as they are typed in.

FACTORY

CODE

CODE 1 - MASTER USER 1 11111

CODE 2 - USER 2 2 22222

CODE 3 - ENGINEER 3 33333

CODE 4 - TELEMONITORING 4 44444

CODE 5 - USER 5 5 55555

CODE 6 - USER 6 6 66666

CODE 7 - USER 7 7 77777

CODE 8 - USER 8 8 88888

Each user is assigned and “identification

number “ (from 1 to 8) that is to be typed

in before the code; this number allows

the unit to identify the user of the system.

To be identified by the system, the owner

must type in the number 1 followed by

his personal code; any other users will

instead type in the number 2, 3, 4, 5, 6,

7 or 8, followed by his personal code

3. System Arming/Disarming

• For ARMING of the system, enter a valid code associated to the 3

sectors and press the

TOTAL

key.

Leds

and

flash, and after 4 seconds they

light up with a fixed light.

If there is an an exit delay, it is indicated by the intermittent sound of the

buzzer.

• To DISARM the system, enter a valid code and press the

TOTAL

key.

Leds

and

corresponding to active sectors

go OFF and thebuzzer beeps twice.

• To partially ARM the system, enter a valid code and press the key for

the zone or zones ne wishes to arm.

to arm Zone 1 - the Led

flashes and lights up with a fixed

light after 4 seconds

to arm Zone 2 - the Led

flashes and lights up with a

fixed light after 4 seconds

to arm Zone 3 - the Led

flashes and lights up with a fixed

light after 4 seconds

• To DISARM the system, enter a valid code and press the

TOTAL

key. The

leds in the previously armed zones go OFF and the buzzer beeps twice.

• During partial arming, about 5 seconds are available (led flashes) within

which it is possible to correct the type of arming; once this time is up,

the leds light up with a fixed light and the sectors are armed.

• After selecting the desired configuration for the zones, arming is

confirmed by pressing the

key without waiting for the time

available for arming to expire.

3.1 Away Arming/Disarming

3.2 Partial Arming/Disarming

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron MP110 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elkron MP110

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info