Bedienungsanleitung Elkron MP110TG (Seite 8 von 20) (Englisch)

741485

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

(((ELKRON)))

MP110 USER MANUAL

(((ELKRON)))

MP110 USER MANUAL

2.1 Storage of a New Key

1. Enter the MASTER USER code on the keypad and press keys

in sequence.

2. Press th

key several times until the following message appears

on the display:

• keypad with alphanumeric display: “KEY PROGRAM”

• keypad with segmented display: “-” (one flashing hyphen)

3. Press the

key. Commutator led 2 flashes slowly to indicate

system standby for entry of the first key.

4. Insert the commutator key. The system proposes key enabling on all

three zones with the lighting of leds 1, 3 and 4. If this is the desired

configuration, remove the key while led 2 flashes quickly.

5. By leaving the key permanently inserted, the various combinations of

zones with which the key can be associated are displayed with the

lighting of leds 1, 3 and 4, as shown in the table below:

6. When the desired combination has been set, remove the key ONLY

WHILE LED 2 FLASHES QUICKLY.

7. Re-insert the key. If the operation has been successfully

performed, the leds of the zones previously associated with the key

will light up and led 2 flashes slowly while standing by for the

programming of any other keys.

slow

flashing

led 1, 3

and 4 ON

1 1 ON 3 ON 4 ON the key is associated with all 3 zones

2 1 ON 3 OFF 4 OFF the key is associated with zone1

3 1 OFF 3 ON 4 OFF the key is associated with zone 2

4 1 ON 3 ON 4 OFF the key is associated with zones 1and 2

5 1 OFF 3 OFF 4 ON the key is associated with zone 3

6 1 ON 3 OFF 4 ON the key is associated with zones 1and 3

7 1 OFF 3 ON 4 ON the key is associated with zones 2 and 3

3.6 Disarming with Antirobbery Code

If the system is equipped with an integrated telephone unit or other remote

transmission system, a panic alarm signal can be sent in case of constraint

to disarm the antirobbery system.

• The disarming procedure described in para 3.1 is carried out, but it is

necessary to enter the secret code increasing the last digit by one unit.

• Example: code 123456 would become 123457; code 132459 would

become 132450.

• Disarm the control unit; if within approx.30 sec the correct code is not

entered the control unit will send the panic alarm to all programmed

telephone numbers.

3.7 Wrong Code

• In case of introduction of a wrong code for 4 consecutive times, the

system visualizes a tamper on the keypads and the readers. When

introducing a wrong code for the fifth consecutive time, the system starts

a tamper alarm.

3.3 Arming with Reduced Code

• It is sufficient to enter the first 2 digits of the code followed by key

TOTAL

for a total arming, or

for a partial arming.

• Quick arming is possible only if the system is fully disarmed.

3.4 Commutating Lock with Open Zones

• If the commutating lock with open zones has been programmed, it will

not be possible to arm –neither from keypad nor by DK key – the sectors

to which the currently open zones are associated. If you try such an

arming from keypad, a relevant warning is provided on the display and

no arming will take place.

3.5 Open Zone Self-Bypassing

• If both commutating lock and self-bypassing have been programmed,

the zones left open are automatically bypassed when an arming from

keypad or DK key is carried out. If the arming is made from keypad, the

self-bypassing is properly signalled on the display. The arming regularly

takes place and no alarm is generated. The self-bypassed zones are

reentered automatically at their re-closing (even with armed system).A

following opening will therefore generate the alarm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron MP110TG Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elkron MP110TG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info