Bedienungsanleitung Elro HA68S (Seite 6 von 34) (Englisch)

536725

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

-61--4-

CHIME

Chime is a low security facility for use when the system is Standby mode. If the

Chime feature is ON, and a detector on a zone that has its Chime function

enabled is triggered, the internal sounder will produce a low volume warning

tone. A typical use of the Chime function would be to warn that a door or

particular area has been accessed.

VOICE DIALER

If the Voice Dialer is enabled and an alarm condition occurs, the system will call

for help using your recorded alarm messages and up to six telephone numbers.

When an alarm condition occurs, the telephone voice dialer (if enabled) will call

the first enabled number in the calling sequence and replay the recorded alarm

messages for the configured ‘Play Time’. The recipient must acknowledge the

message by pressing the button on their telephone keypad. If the call is

unanswered or an acknowledgment is not received then the next active number

in the dialing sequence will be called. The dialer will continue calling each

number in turn until either all numbers in the sequence have been dialed the set

number of times or the sequence is cancelled/acknowledged by the recipient.

DIGITAL DIALER

As an alternative to the Voice dialer the system may be configured to interface

with a central monitoring station.

LATCH KEY

When the system is disarmed the Latch-Key facility, if enabled, will call the first

latchkey phone number and replay the user message (recorded under user

setup) for the set ‘Play Time’. The recipient must acknowledge the message by

pressing the button on the telephone keypad. If the call is unanswered or

an acknowledgment is not received then the second latchkey phone number will

be called. The voice dialer will continue calling each number in turn until each

number has been dialed the set number of times or the sequence is

cancelled/acknowledged by the recipient.

For example, the latchkey facility is useful to inform parents that a child has

returned from school and disarmed the system.

REMOTE SYSTEM CONTROL

It is possible to dial into the system via the connected telephone line to

interrogate the system status and to have basic control over the system, (e.g. to

Arm and Disarm the system). You may also activate the microphone on the

control panel to Listen-In to what is happening in the protected property.

TAMPER PROTECTION

All system devices (except the Remote Control Units) incorporate Tamper

protection features to protect against unauthorized attempts to interfere with

the device. Any attempt to remove the battery covers from any device (except

the Remote Control) or to remove the Solar Siren or Control Panel from the wall

will initiate an alarm condition (unless the system is in Test or Programming

modes), even if the system is Disarmed.

PIR DETECTORS

Under low battery conditions the LED behind the detector lens will flash when

movement is detected to indicate that the battery needs to be replaced.

Under normal battery conditions the LED does not illuminate unless the PIR

detector is in Walk Test mode.

MAGNETIC CONTACT DETECTORS

Under low battery conditions, when the Detector is activated the transmit LED

will be illuminated for approximately 1s as the door/window is opened.

Under normal battery conditions the LED will not illuminate as the Detector is

operated, (unless the Detector is in Test Mode with the battery cover removed).

MAINTENANCE

Your Alarm System requires very little maintenance. However, a few simple

tasks will ensure its continued reliability and operation.

CONTROL PANEL

The rechargeable batteries have a typical life of 3-4 years and need no

maintenance during this period, provided they are kept charged. The batteries

will be damaged if they are stored in a discharged state for long periods.

DETECTORS AND REMOTE CONTROL

The Detectors require very little maintenance. The batteries should be replaced

once a year or when a low battery status is indicated.

IMPORTANT: Should you, for any reason, have to completely power-down the

system (e.g. to move the system to a new premises) first put the system into

Test mode before removing the Control Panel cover and disconnecting the power

supply and backup batteries.

Remote Controls 1 x 3V CR2032 Lithium Cells

(or equivalent)

Magnetic Contact 1 x 3.6V 1/2 AA Size Lithium Cells

Detectors (or equivalent)

PIR Detectors 1 x 3.6V 1/2 AA Size Lithium Cells

(or equivalent)

ENEN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro HA68S Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro HA68S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info