Bedienungsanleitung Elro HIS20SF (Seite 8 von 62) (Deutsch, Englisch, Holländisch, Französisch)

536726

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

REMOTE CONTROL UNIT

A LED indicator F Key Chain Ring

B Fully Arm/Holiday Arm G Battery Cover

C Night Arm/Partial Arm H Negative Polarity

D Disarm I Positive Polarity

E Panic Switch

The Remote Control Unit is used to Fully Arm/Holiday

Arm, Night Arm/Partial Arm and Disarm the system.

The Remote Control also incorporates a Panic switch.

Activating the Panic switch will immediately initiate a

Full Alarm condition whether the system is Armed or

Disarmed, (unless the system is in Service, Test or

Program mode).

The Remote Control adopts a CR2032 type Lithium cell

which under normal conditions will have typical life in

excess of 1 year. Under normal battery conditions the

LED on the Remote control will only illuminate when a

button is pressed. However, under low battery

conditions this LED will flash every time the button is

pressed. When this occurs the batteries should be

replaced as soon as possible.

SETTING THE REMOTE CONTROL

1. Remove the rear cover by undoing the small screw

on the rear of the Remote Control.

2. Insert the battery ensuring that the +v terminal

faces upwards away from the PCB.

3. Replace the rear cover and fixing screw.

4. In order to communicate with the Smart Home Box,

the ID code of the Remote Control needs to be

learned by the Smart Home Box.

a. Set the Smart Home Box into ‘1. User Setup’

and press .

b. Select which administrator/user will carry the

remote control and press .

c. Select ‘:7 Remoter’ and press .

d. ‘7-1 LearningID’ will be shown and press

By pressing the , or on the Remote

Control will emit the ID code to the Smart Home

Box instantly.

SMART HOME BOX

LOCATING THE SMART HOME BOX

When choosing a suitable location for the Smart Home

Box, the following points should be considered.

1. The Smart Home Box should be located in a

position out of sight of potential intruders and in a

safe location, but easily accessible for system

operation.

2. The Smart Home Box should be mounted on a

sound flat surface to ensure that the rear tamper

switch on the Smart Home Box is closed when the

Panel is mounted. The Smart Home Box should

be mounted at a convenient height of between

1.3m and 1.5m and in a position where it will be

seen each day.

Note: If small children are in the household, a

further consideration should be given to keeping

the units out of their reach.

3. It is recommended that the Smart Home Box

should be positioned such that the Exit/Entry tone

(emitted by the Smart Home Box) can be heard

from outside the property.

4. The Smart Home Box should be mounted within a

protected area so that any intruder cannot reach

the Smart Home Box without opening a protected

door or passing through an area protected by a

PIR detector when the system is armed.

5. The Smart Home Box must be located within reach

of a mains socket.

6. If the telephone based functionality is to be used

then the Smart Home Box will need connecting to a

convenient telephone point.

Note: It is recommended that the telephone

connection lead is not extended beyond 5m before

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro HIS20SF Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info