Bedienungsanleitung Elro HIS20SF (Seite 9 von 62) (Deutsch, Englisch, Holländisch, Französisch)

536726

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

connecting to a telephone master or secondary

outlet.

7. Do not locate the Smart Home Box closer than 1m

to any large metallic object, (e.g. mirrors, radiators,

etc) as this may affect the radio range of the Smart

Home Box.

MOUNTING THE SMART HOME BOX

1. Undo the two captive fixing screws on top of the

panel and open the cover. The cover is hinged

along the bottom edge.

2. Unclip and remove the two back-up batteries on

upper and lower right hand side of the panel.

3. Route the cable from the Power Supply Unit up

behind along the cable track on the right hand side

of the Smart Home Box, and connect the plug to

the DC power socket in the panel. Ensuring that

the cable is not trapped between the panel and the

wall.

4. Use the fixing template provided (p.56) to mark

the position of two fixing holes on the wall.

Drill two holes, and insert the supplied plastic wall

plugs and then fit two screws into the wall plugs

until almost fully home. Hang the Smart Home

Box over these screws using the two keyhole slots

on either side of the top corners of the panel

casing.

5. Fix the Smart Home Box by inserting a fixing screw

into the lower fixing hole in the panel and tighten

the screw until it just grip the casing. Do not over

tighten the fixing screws as this could damage or

distort the casing.

6. Ensure that the ‘Reset’ (P1) and the ‘Hard-Wired

Siren tamper detect’ (P51) jumper links are set in

the OFF position.

7. Connect battery leads to both back-up batteries

and refit batteries.

Battery 1 (upper): Blue lead to +ve battery terminal

Black lead to –ve battery

terminal

Battery 2 (lower): Red lead to +ve battery terminal

Blue lead to –ve battery terminal

IMPORTANT: Take care when connecting battery

leads to the batteries as connecting incorrectly

could damage the batteries or the Smart Home

Box.

Note: The Power LED may flash to indicate that

the unit is being operated from the back-up

batteries and that mains supply is not present.

8. If fitted, remove the plastic film covering the LCD

display and on the display window on the cover.

9. Close the lid of the Smart Home Box and tighten

the captive fixing screws.

10. Plug in and switch ON the Power Supply Unit, (the

Power LED should illuminate).

11. If required, connect the Smart Home Box to the

telephone line using the cable supplied by inserting

small RJ11 plug into socket marked LINE located

on the bottom edge of the Smart Home Box.

If the cable supplied is not long enough to reach a

suitable phone point then it will need extending

using a coupler and extension lead (not supplied).

Note: If the Tamper of Smart Home Box alarm

sounds during the installation reset the alarm by

pressing:

, ,

on the Smart Home Box Keypad.

Cable Track

Smart Home Box

Fixing Template

Fixing Hole

Keyhole Slots

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro HIS20SF Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info