Bedienungsanleitung ELV WS2300 (Seite 5 von 19) (Englisch)

542403

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

GB GB

To operate using cable connection, simply use the enclosed 10 meter

cable and connect the thermo-hygro sensor to the base station. Once

the connection is detected, the base station will automatically con-

tinue reading the data from the sensor.

1. Low battery indicator

2. DCF77 radio controlled time icon

3. Date display

4. Time zone display

5. Date, seconds, alarm time and time

zone

6. Alarm icon

7. Weather forecast icons

8. Weather tendency indicator

9. Pressure alarm display

10. hPa/inHg air pressure unit

11. Pressure units (relative or absolute)

12. 433MHz reception icon

13. Rainfall display

14. Indoor, outdoor, humidity, dew point,

wind chill, rainfall alarm icon

15. 24h, 1h or total hour display

16. Humidity display as RH%

17. Rainfall units (inch or mm)

18. Temperature display units (ºC or ºF)

19. Outdoor temperature/humidity display

20. Indoor temperature/humidity display

21. Dew point temperature display

22. Wind chill temperature display

23. Wind alarm icon

24. Wind information for Min/Max speed

and wind speed low, high, direction

alarm

25. Wind direction and speed (m/s, knots,

Beaufort, km/h or mph) display

26. Alarm buzzer ON/OFF icon

27. General alarm icon

The user may at any time switch from cable connection to using

433MHz (or vice versa) by simply disconnecting (or connecting) the

cable from the base station to the sensor. When the base station

detects no cable connection to the sensors, the existing data reading

interval is changed to the new reading interval, i.e. using cable con-

nection is every 8 seconds data reading interval or from 32 seconds -

128 seconds intervals when using 433MHz (depending on wind

speed)

Using the AC adaptor to operate the base station will also supply

power to the sensor if the cable is connected to it. Batteries used for

433MHz transmission may be left in the sensor when using cable

connection for power back-up in case of AC power failure. A loss of

power would desynchronize the base station and the sensor and no

weather data will be received. To Synchronize the units so that the

weather data can be received, press and hold the PLUS(+) for 2 sec-

onds. However in general, batteries that will not be used for long

periods should be removed to avoid leakage.

Wireless 433MHz transmission:

Using 433MHz wireless transmission of weather data from the sensor

to the base station will provide users greater freedom as to where

units can be positioned without the need to be restricted by cable.

Note:

If no outdoor weather data is displayed or the signal to the sensors is

lost during setting up, mounting, changing of batteries to the sensor or

plugging or unplugging cables, simply press and hold the PLUS(+)

key for 2 seconds and a short beep will sound to synchronize the

base station to sensors. Without being synchronized, weather data

will not be received.

7. LCD Overview

The following illustration shows the full segments of the LCD for

description purposes only and will not appear like this during

normal operation and use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ELV WS2300 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info