Bedienungsanleitung ELV WS2300 (Seite 6 von 19) (Englisch)

542403

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

8. Function test:

Once the weather station is powered up, perform a function test by

checking that the weather data is received. To do this, press the

either DISPLAY, PRESSURE or WIND keys to toggle through the

relevant LCD sections:

1) Indoor temperature and humidity

2) Outdoor temperature and humidity

3) Outdoor wind chill

4) Dew point

5) Rainfall 24 hour

6) Rainfall 1hour

7) Rainfall Total

8) Relative and absolute pressure

9) Wind speed, wind direction and wind direction in degrees

If any readings cannot be received from the sensors, lines (- - -) will

be displayed in the respective weather sections of the LCD. In this

case, check that all cables are correctly inserted into the correct

sockets and press and hold the PLUS(+) key for 2 seconds and a

short beep will sound to synchronize the base station to the sensors

otherwise no weather data will be received.

Some weather readings such as wind speed and direction may not

appear immediately on the LCD if the wind-fan or vane of the wind

sensor is moved. This is due to the set reading time intervals for the

wind readings. However the current wind speed or direction will be

displayed once the time reading interval is reached. For rainfall, the

interval readings may take up to 2 minutes before the data is dis-

played on the LCD.

GB GB

9. Mounting

Important Note

Prior to drilling mounting holes and permanently affixing any of the

units, please ensure the following points are considered:

• Cable lengths of the units meet with your distance requirements

at the point of fixing

• Signals from the sensors can be received by the base station at

points of mounting

• Radio controlled time signal can be received at the point of

mounting

Base Station

With two foldable legs at the back of the unit, the base station can be

placed onto any flat surface or wall mounted at the desired location by

the hanging holes also at the back of the unit. It is important to check

that the 433MHz (if using wireless connection) and the DCF77 radio

controlled time signal can be received before permanently mounting

any of the units. Should the base station not display the 433MHz

weather data from the sensors or the radio controlled time from the

desired location, then relocate the units. Once the signals are re-

ceived, the system can be affixed. Also if you have selected to use

cable connection, ensure that distances can reach all desired loca-

tions before affixing any unit permanently

Mounting the Wind Sensor onto a mast

Wind-fan

Wind-vane

Mast

Firstly, check that the wind-fan and the wind-vane can rotate freely

before fixing the unit. For correct and accurate readings it is impor-

tant to mount the sensor so that the front (marked E) is pointing in

East-West direction. The wind sensor should now be mounted using

the screw provided onto a mast to allow the wind to travel around the

sensor unhindered from all directions (ideal mast size should be from

Ø16mm – Ø33mm).

Once the wind sensor is fixed onto the mast, connect the cable to the

corresponding thermo-hygro sensor socket so that operating power

supply can be received and data can be transmitted to the base sta-

tion.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ELV WS2300 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info