Bedienungsanleitung EMOS 5001 (Seite 4 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

784674

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

wireless sensor: transmission frequency 433 MHz, 10 mW e.r.p. max.

station power supply: 3× 1.5 V AAA batteries (not included)

adapter AC 230 V/DC 5 V, 300 mA (included)

sensor power supply: 2× 1.5 V AAA (not included)

station dimensions and weight: 17 × 192 × 127 mm, 364 g

sensor dimensions and weight: 15 × 62 × 100 mm, 54 g

Getting Started

1. Connect the adapter to the station, then insert batteries rst into the weather station (3× 1.5 V

AAA), then into the wireless sensor (2× 1.5 V AAA). The battery compartment of the sensor is

protected by screws; use a suitable screwdriver.

2. When inserting the batteries make sure the polarity is correct to avoid damaging the weather

station or sensor. Only use alkaline batteries of the same type; do not use rechargeable batteries.

3. Place the two units next to each other. The weather station will automatically detect the sensor

signal within 3 minutes. If signal from the sensor is not detected, long-press the button on

the weather station to repeat the search.

4. We recommend placing the sensor on the north side of the house. The range of the sensor may

decrease substantially in areas with large number of obstacles.

5. The sensor is resistant to dripping water; however, it should not be exposed to sustained rain.

6. Do not place the sensor onto metal objects as this will reduce its transmission range.

7. If the low battery icon is displayed, replace batteries in the sensor or weather station.

Switching Channel and Connecting Additional Sensors

1. Choose the desired channel 1, 2, or 3 for the sensor by repeatedly pressing the button. Then,

long-press the button; the icon will start ashing.

2. Unscrew the cover from the battery compartment on the rear of the sensor and set the sensor

switch to the desired sensor channel number (1, 2, 3), then insert batteries (2× 1.5 V AAA). Data

from the sensor will be loaded within 3 minutes.

3. If sensor signal is not found, remove the batteries and proceed again in accordance with steps

1 and 2 or press the TX button.

Displaying Data from Multiple Sensors, Automatic Cycling through Values from

Connected Sensors

Press the button repeatedly to display data from all connected sensors on the weather station,

one by one.

You can also activate cycling through data from all connected sensors:

1. turning on cycling

Repeatedly press the button until the display shows the icon.

Data from all 3 sensors will be shown automatically and repeatedly one after another.

2. turning o cycling

Repeatedly press the button until the icon disappears.

Radio Controlled Clock (DCF77)

The wireless sensor will automatically start searching for DCF77 (hereinafter referred to as DCF)

signal for 5 minutes after pairing with the weather station; the icon is ashing. (The DCF sensor

is located in the sensor).

Signal detected – the icon stops ashing and displays the current time with the DCF icon .

Signal not detected – DCF icon will not be displayed. DCF signal will be synchronised daily between

2:00 and 3:00 am.

Note: If the weather station detects DCF signal but the current time on the display is incorrect (e.g.

shifted ±1 hour), you must always set the correct time zone for the country where you are using the

station, see Manual Settings.

In standard conditions (at safe distance from sources of interference, such as TV sets or computer

monitors), the reception of time signal takes several minutes. If the weather station does not detect

the signal, follow these steps:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EMOS 5001 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info