Bedienungsanleitung EMOS SELECT 5002 (Seite 4 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

784682

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

GETTING STARTED

WIRELESS SENSOR

1. Remove the battery door.

2. Insert 2 x AA size batteries into the battery compartment. Make sure you insert

them the right way according to the polarity information marked on the battery

compartment.

3. Close the battery door.

Note:

- This wireless sensor can receive the Radio controlled clock signal for main unit auto

time setting. Just pair up the sensor with main unit to apply this function.

- Once the channel is assigned to a Wireless Hygro-Thermo sensor, you can only

change it by removing the batteries or resetting the unit.

- Avoid placing the sensor in direct sunlight, rain or snow.

MAIN UNIT

1. Plug the power adapter to power up the main unit.

2. Once the main unit power up, it will enter normal time mode.

Note:

- You can using AAA batteries for backup purpose, remove the battery door and

install 3 new AAA size batteries as per the polarity information marked on the battery

compartment, then close the battery door.

- If no display appears on the LCD after installing the batteries, press the [ RESET ] key

by using a metal wire.

- To avoid the wireless sensor and main unit pairing fail, please power up the sensor(s)

rst, and then press [ RESET ] key in main unit after sensor setup.

- You may not receive the signal immediately. Due to the atmospheric disturbance, the

best reception often occurs during night time.

WIRELESS SENSOR SIGNAL RECEIVING

1. In normal mode, press [ SENSOR ] key once to start receiving the sensor signal of

current on displaying channel. The signal icon will ash.

For example, when CH 1 is displayed, pressing [ SENSOR ] key will start receive for

CH 1 only.

2. The signal icon will ash until the reception succeeded. If no signal is received within

5 minutes the icon will disappear.

Receiving wireless signal after manual reset or the [

SENSOR ] key is pressed

When waiting for signals, “--” will display in the readings

eld

Good wireless sensor signal

3. If the signal for Ch 1~8 has discontinued and

does not recover within 1 hour, the signal icon

will disappear. The temperature and humidity will

display “Er” for the corresponding channel.

4. If the signal does not recover within 48 hours, the

“Er” display will become permanent you need to

replace the batteries of “Er” channel’s sensors and

then press [ SENSOR ] key to pair up the sensors

of each “Er” channels again.

Note:

After replacing the batteries of the wireless sensor or the unit fails to receive wireless

sensor signal of a specied channel. During the failed channel is displaying, press

[ SENSOR ] key to manually receive that sensor signal again.

VIEW CHANNEL OF MULTIPLE WIRELESS SENSORS

1. In normal mode, press [ CHANNEL / + ] key to switch the display between CH 1~8.

2. In normal mode, press and hold [ CHANNEL / + ] key for 2 seconds to enter auto-

cycle mode, after a bi sounds, it will alternately displays the channels at 4 second

intervals.

3. During auto-cycle mode, press [ CHANNEL / + ] key once to stop auto-cycle and

display the current channel.

4. Using auto-cycle mode will only display the communicated channels. For example,

when CH 1 and 6 have received the signal from the corresponding sensor, holding [

CHANNEL / + ] key for 2 seconds will only toggle the readings of CH 1 and 6. Other

channels will be neglected.

CH 1 CH 6 CH 1

RECEPTION OF RADIO CONTROLLED SIGNAL

The time and date are radio-controlled. The current time and date are automatically

synchronized with the signal that transmitted from RC station through wireless sensor.

Please make sure the wireless sensor is connected to the main unit.

RCC SIGNAL STRENGTH INDICATOR

The signal indicator shows signal receive status. Flashing wave segment means RCC

signals are being received. The signal receiving status could be classied into 2 types:

No RCC signal received Received RCC signal

Note:

- Every day the wireless sensor will automatically search for the time signal at 2:00 and

17:00.

- Always place the unit away from interfering sources such as TV set, computer, etc.

- Avoid placing the unit on or next to metal plate.

- Closed area such as airport basement, tower block or factory is not recommended.

- Do not start reception on a moving article such as vehicle or train.

DAYLIGHT SAVING TIME (DST)

This clock has been programmed to automatically switch when the daylight saving time is

in effect. User can disable the DST function in time and calendar setting mode.

Note:

DST AUTO/OFF setting only available when RCC function is ON.

TIME AND CALENDAR SETTING

1. In normal mode, press and hold [ TIME SET ] key for 2 seconds to enter date and

time setting mode.

2. Press [ CHANNEL / + ] or [ MEM / - ] key to adjust the setting.

3. Press [ TIME SET ] key to enter the next setting

4. The setting sequence: 12/24H hour minute second year DM/

MD month day time zone language RCC ON/OFF DST

AUTO / OFF

5. When you complete the setting, press [ TIME SET ] key or leave the unit for 60

seconds to return to normal mode.

Note:

DST AUTO/OFF setting only available when RCC function is ON.

12/24H setting

Hour/Minute/

Second setting

Year setting

Month/Day

setting D/M M/D

Month/day

setting M/ D

Time zone

setting

00H 01H...23H -23H...-01H 00H

Language

setting

EN FR DE ES IT NL RU

RCC setting

DST (day light

saving) setting

ALARM TIME SETTING AND DISPLAY

1. In normal time mode, press and hold [ ALARM ] key for 2 seconds until the alarm

hour digit ashes to enter alarm time setting mode.

2. Press [ CHANNEL / + ] or [ MEM / - ] key to change the value. Press and hold the

key for quick-adjust.

3. Repeat the above operations to set the alarm time in this order: Hour → Minute.

4. When you complete the setting of Minute, Press [ ALARM ] key or leave the unit for

60 seconds to return to normal mode.

EMOS SELECT 5002 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info