Bedienungsanleitung Emtec 4in1 (Seite 7 von 65) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch)

122716

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

Note: As you can dedicate any appliance (TV, DVD, SAT...) to the

VCR,DVDorSATkeys,youneedrsttoenterany4digitcodefor

thekindofapplianceyouwishtocontrol(foundinthecodebook,i.e.:

IfyouwanttoprogramaSATundertheVCRkey,enteranySATcode

foundinthecodebookandthenfollowthestepsbelow:

1. Turn on the device you want to control.

2. Press and hold SETUP (4) until the LED indicator (1) lights stea-

dily. Release SETUP button.

3. Press the mode button (3) that matches the equipment you wish to

control.TheLED(1)blinksonce.

4. PressPROG+(7)once.Afterafewsecondstheremotestarts

stepping through the code library (fast search, 1 code per second).

Whenthedeviceresponds,youcanpressPROG+(7)toswitchto

slowsearch(1codeper3seconds).Youcanstepbackbypressing

PROG-(7)(youcanstepforwardbypressingPROG+(7)incaseyou

wenttoofarback).Assoonasthedevicerespondsagain,pressthe

-ENTkey(15)tostorethecodeyoufound.

7) Brand search

If your brand is listed hereafter, you have the possibility to use the

brand search method (faster than the «manual» and the «automatic

code search»):

BRAND CODE

Philips/Radiola    1

Sony/Panasonic/JVC/SharpAkai/Toshiba/Daewoo 2

Thomson/Brandt    3

Telefunken/Saba/Normende   4

Grundig/Blaupunkt    5

Nokia/ITT     6

1. Turn on the device you want to control.

2. Press and hold SETUP (4) until the LED indicator (1) lights stea-

dily. Release SETUP button.

3. Pressthemodekey(3)thatmatchestheequipmentyouwantto

control (for example TV).

4. Enter the code corresponding to your brand, point the 4 in 1

Universal Remote Control in the direction of your equipment, press

onceonlyPROG+(7)continuetopointthe4in1UniversalRemote

Control at your equipment until the equipment changes channel. (The

remote control sends an IR signal every second. So please wait until

your equipment reacts). When your equipment does react, press on

thekeyENT(15)toconrm.Ifaccidentallyyoumissthecode,you

can stop the autosearch by pressing PROG – (7) and by repeatedly

pressingthiskeyreturntotherightcode.PressENT(15)toconrm.

8) Identifying codes found using the search procedure

1. Press and hold SETUP (4) until the LED indicator (1) lights stea-

dily. Release SETUP.

2. Pressthemodekey(4)fortheequipmentyouwanttoidentify(TV,

VCR,DVDorSAT).TheLEDblinksonce.

3. PressagainSETUP.TheLEDblinksonce.

4. Toidentifytherstdigitpresseachnumberbuttonfrom0–9(13)

untiltheLEDblinks.Thenumberyoupressedistherstdigitofthe

code.

5. Presseachnumberkeyfrom0–9asabovetondthesecondand

third digit.

7. Presseachnumberkeyfrom0–9asabovetondthefourthdigit.

When the fourth digit has been found the LED will go off. Don’t

forget to write down the code on the label of the battery compartment.

9) Volume Control

AdjustmentofALLvolumecontrolsunderaspecicmode

You can program the remote control so that the volume and mute

keyscontrolaspecicdevice(thevolumecontrolmustexistonthe

corresponding device). E.g. control of TV sound in TV mode, VCR

mode and SAT mode.

1. Press and hold SETUP (4) until the LED indicator (1) lights stea-

dily. Release SETUP.

2. PressandholdMUTE(10)untiltheLED(1)blinksonce.Release

MUTE.

3. Pressonceonthemodekey(TV,SAT,…)correspondingtothe

device whose volume will always be controlled by the VOL (8) and

MUTE(10)keys.

4. PresstheMUTE(10)keyonce.

Adjustment of the volume controls for EACH mode.

You can program the remote control so that the volume control is

functional for each mode selected (the volume control must exist on

the corresponding device). E.g. control of the television set sound in

TV mode, control of the SAT receiver sound in SAT mode,...

1. Press and hold SETUP (4) until the LED indicator (1) lights stea-

dily. Release SETUP.

2. PressandholdMUTE(10)untiltheLED(1)blinksonce.Release

MUTE.

3. Pressonceonthemodekey(TV,VCR,…)correspondingtothe

device whose volume will always be controlled by the VOL (8) and

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Emtec 4in1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info