601365

Enduro EM405 Seite 41

41
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
ENDURO
®
EM405 S 35
Ref: EM405 S-UM-TKI-0115-Rev.A.
Green LED (Fig. 5H) is blinking, no buzzer: no communication between handset and control unit. This could
be because of too much distance between remote control handset and control unit, or the battery isolation
switch for manoeuvring system is not turned on or that there is a distortion signal disturbing the
communication. As soon as connection is good again the green LED will be continue on and the system is
ready to use.
Blue battery voltage LED (Fig. 5N) is blinking in combination with buzzer (2 times blinking, break, 2 times
blinking, break etc.): Battery voltage too low (<10V). Battery needs to be recharged.
Blue battery voltage LED (Fig. 5N) is blinking in combination with buzzer (4 times blinking, break, 4 times
blinking, break etc.): Battery Voltage too high (over charged). Try to discharge the battery by turning on a
user (for example a lamp or water-pump).
Red overload LED (Fig. 5L) is blinking in combination with buzzer (6 times blinking, break, 6 times blinking,
break etc.): Amp overload protection is activated. Wait about 60 seconds and try again.
Blue 9V battery LED (Fig. 5M) is blinking, no buzzer: The internal 9V battery is near empty and needs to be
replaced.
Changing batteries in the remote control:
When the battery is empty (blue 9V battery LED (Fig. 5M) is blinking), it needs to be replaced.
Open the rear cover of the handset (Fig. 7A).
Take out the dead/old battery and dispose in the appropriate way.
Install a new replacement battery (Fig. 7.1). Make sure to use a leak proof PP3 (9Volt) battery (No claims
under guarantee can be considered for damage caused by leaking batteries).
Close the rear cover again.
Dead and used batteries may leak and damage the remote control handset! Remove the batteries if the
handset is not going to be used for an extended period.
OPERATION - ELECTRONIC CONTROL UNIT
The electronic control unit (4), which is mounted inside your caravan, is responsible for controlling the
manoeuvring system.
The control unit has three LED’s, one pushbutton and one slide switch (Fig. 3):
Green LED (Fig. 3B): Power LED continuously illuminated
when system is activated (by moving slide switch to
“On”-I). If the handset far away from the control unit, beyond the availably distance, this LED will go out.
Blue LED (Fig. 3C): Error message LED concerning caravan battery:
Blue LED is blinking (2 times blinking, break, 2 times blinking, break etc.): Battery voltage too low (<10V).
Battery needs to be recharged.
Blue LED is blinking (4 times blinking, break, 4 times blinking, break etc.): Battery Voltage too high (over
charged). Try to discharge the battery by turning on a user (for example a lamp or water-pump).
Red LED (Fig. 3D) is blinking (6 times blinking, break, 6 times blinking, break etc.): Amp overload protection is
activated. Wait about 60 seconds and try again.
In general all error messages will reset automatically after one minute. If this is not the case, reset the
electronics of the manoeuvring system by switching off the system via the isolation switch and the remote
control handset for at least 15 seconds and then turning it on again.
The Reset Button (Fig. 3A): The remote control handset and the control unit are synchronised with each other
in the factory. If the control unit or the remote control handset is replaced, they must be re-synchronised as
described below:
Check the installation in accordance with the installation instructions and ensure that the drive rollers are
not applied. Check that the battery is properly connected, check the condition of the battery and that a
voltage of 12 V is present at the control unit.
Please ensure that the battery isolation switch is on.
Activate the remote control handset by sliding the slide switch to “On”-I (Fig. 5A). The green LED on the
remote control handset (Fig. 5H) starts to flash slowly.
Press the reset button (Fig. 3A) on the control unit. All three LED’s on the control unit (Fig. 3B, 3C & 3D)
will flash slowly.
Press both forwards (Fig. 5B) and reverse (Fig. 5C) button on the remote control handset for about 3
seconds. Then the handset buzzer will give a short beep to confirm that the synchronisation is complete.
After successful synchronisation, the green LED on the control unit (Fig. 3B) and on the remote control
handset (Fig. 5H) will illuminate continuously.
The single/twin axle function switch (Fig. 3S/T): The EN
DURO
®
EM405 Caravan manoeuvring system is
suitable for both single axle and twin axle caravans. You just need to pull the single/twin axle function switch
(Fig 3S/T) on the control unit, so that the manoeuvring system can be used for a single axle caravan or a twin
axle caravan (for 2 motor use but also for 4 motor use). In the twin axle function the all wheels will drive but at
a different speed.
… 41 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

enduro-em405

Suche zurücksetzen

  • Rollen rücken nicht ein noch aus, blaue Kontrolleuchte reagiert nicht Eingereicht am 31-10-2022 17:02

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Enduro EM405 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info