ENDURO® EM515FL 42
Ref: EM515FL-UM-TKI-0323-Rev.B.
The automatic engaging system:
To activate the automatic engaging system of the motor powered rollers on the tyre, press the two buttons for
engaging (Fig. 8I) or disengaging (Fig. 8J) for at least three seconds. The engaging icon (Fig. 8K) or
disengaging icon (Fig. 8O) will blink fast during these three seconds and every second there will be a beep. This
warns you that the system will be activated!
Engaging: After these three seconds the motor powered rollers will be pressed against the tyre, and the
engaging icon will illuminate constant. Now you can release the two buttons. When the motor powered rollers
are pressed on the tyre strongly enough you hear a short beep, the engaging icon will switch off and the
system is ready to use.
Disengaging: after these three seconds the motor powered rollers will be released from the tyre, and the
disengaging icon will illuminate constant. Now you can release the two buttons. When the motor powered
rollers are completely disengaged you hear a short beep, the disengaging icon will switch off and is the system
ready for transport.
The level display:
The ENDURO® EM515FL is provided with a level display on the remote handset (Fig. 8O, 13, 14). During
manoeuvring you can already see if your caravan is level.
The display shows which side is the lowest. This is made visible in the longitudinal direction (front/rear) and in
the width direction (left/right). With the aid of the jockey wheel, the "longitudinal direction" level to be
adjusted, and with the help of, for example, a drive block or leveller under the wheel, the "width direction" level
can be adjusted. If the caravan is level (approximate) only the central point will light up.
The remote handset switches off:
After 3 minutes, if no button is pressed: After 2 minutes the buzzer will beep for 5 times with a repetition
after 3 minutes. Than the system switches in the “stand-by” modes.
After 6 minutes, if one of the movement buttons is permanently held down: After 5 minutes the buzzer will
beep for 5 times with a repetition after 6 minutes. Than the system switches in the “stand-by” modes.
The manoeuvring system icon (Fig. 8V) and the communication icon (Fig. 8H) turn off and the remote handset
is in the “stand-by” modes which means that there always will be used some current which causes the batteries
to go down. So always make sure the remote handset is turned off by the slide switch.
To reactivate the remote handset, move slide switch down and after approximately 1 second up again.
Error messages via the remote handset:
Communication icon (Fig. 8H) off, no buzzer: remote handset is turned off and also system is not activated
Communication icon (Fig. 8H) continue on, no buzzer: remote handset is turned on and system is activated
and ready to use.
Communication icon (Fig. 8H) is blinking, no buzzer: no communication between handset and control unit.
This could be because of too much distance between remote handset and control unit, or the battery
isolation switch for manoeuvring system is not turned on or that there is a distortion signal disturbing the
communication. As soon as connection is good again the icon will be continue on and the system is ready
to use.
Caravan battery icon (Fig. 8N) is blinking in combination with buzzer (2 times blinking, break, 2 times
blinking, break etc.): Battery voltage too low (<10V). Battery needs to be recharged.
Caravan battery icon (Fig. 8N) is blinking in combination with buzzer (4 times blinking, break, 4 times
blinking, break etc.): Battery Voltage too high (over charged). Try to discharge the battery by turning on a
user (for example a lamp or water-pump).
Overload icon (Fig. 8L) is blinking in combination with buzzer (6 times blinking, break, 6 times blinking,
break etc.): Amp overload protection is activated. Wait about 60 seconds and try again.
Remote handset batteries icon (Fig. 8M) is blinking, no buzzer: The batteries are near empty and need to
be replaced.
Changing batteries in the remote handset:
When the batteries are empty (Remote battery icon (Fig. 8J) is blinking), they need to be replaced.
Open the rear cover of the remote handset (Fig. 9).
Take out the dead/old batteries and dispose in the appropriate way.
Install a new replacement batteries (Fig. 9). Make sure to use leak proof AAA (1.5 Volt) batteries (No
claims under guarantee can be considered for damage caused by leaking batteries).
Close the rear cover again.
Dead and used batteries may leak and damage the remote handset! Remove the batteries if the remote
handset is not going to be used for an extended period.
Always make sure that the batteries of the remote handset are in good condition so that it is always ready for
use!
