Please make sure you read the safety instructions very carefully and make sure that you
follow these guidelines!
Make sure that the battery that supplies the system is fully charged and in good condition.
Make sure that the caravan is free from the vehicle and the handbrake is on. Also make sure
that the corner steady feet are fully raised.
Turn on the battery power isolation switch (33).
Activate the manoeuvring system by moving slide switch (Fig. 8A) on the remote handset up. The manoeuvring
icon (Fig. 8V) and the communication icon (Fig. 8H) on the remote handset will illuminate and you will hear a
short beep. The remote handset is ready for use.
Press at the same time, during at least three seconds, the two buttons for engaging the motor powered rollers
(Fig. 8I). The engaging icon (Fig. 8H) will blink fast during these three seconds and every second there will be a
beep. This warns you that the system will be activated!
After these three seconds the motor powered rollers will be pressed against the tyre and the engaging icon will
illuminate constant. Now you can release the two buttons. When the motor powered rollers are pressed on the
tyre strongly enough, you hear a short beep, the engaging icon will switch off and is the system ready to
manoeuvre. The colour of the traction indicator (Fig. 5.1F) should be into the green area.
Before operating the manoeuvring system, release the handbrake.
Now you can choose the movements according the symbols shown on the remote handset. Straight forward
(Fig. 8B), straight reverse (Fig. 8C), left forward (Fig. 8D), left reverse (Fig. 8F), right forward (Fig. 8E), right
reverse (Fig. 8G).
In addition, the left forward (Fig. 8D) and right reverse (Fig. 8G) buttons or right forward (Fig. 8E) and left
reverse (Fig. 8F) buttons may be pressed at the same time to turn the caravan around on its own axis without
moving forward or backward (this function just can work under the “single-axle function”).
When you drive straight forwards or reverse (press button 8B or 8C), it is also possible to adjust the direction
by additional pressing button 8D or 8E (when driving forwards) or button 8F or 8G (when driving reverse).
Because of the “soft start” technology, the caravan will slowly speed up. Because of the “soft stop” technology,
the caravan will stop slowly. This allows you to manoeuvre your caravan even more accurately without any
shocks.
WARNING: When the buttons on the remote handset are released, the caravan will slowly
stop after 0.5 second and continue to move about 6cm (depending on final speed). When
the buttons of the remote handset are released when the system is still in the “soft start”
stage (slowly speed up), the caravan will stop immediately.
After the “soft start” stage the caravan moves according one fixed speed. The speed can increase a little when
going downhill and decrease a little when going uphill.
TIP: The manoeuvring system is more efficient when reversing the caravan up an incline.
During manoeuvring you can already see if your caravan is level. The display shows which side is the lowest
(Fig. 13). This is made visible in the longitudinal direction (front/rear) and in the width direction (left/right).
With the aid of the jockey wheel, the "longitudinal direction" level to be adjusted, and with the help of, for
example, a drive block or leveller under the wheel, the "width direction" level can be adjusted. If the caravan is
level (approximate) only the central point will light up.
You can also level the caravan automatically by using the Finding Level function. See the separate chapter
OPERATION – Finding Level for this.
When you are ready with manoeuvring you need to secure the handbrake.
Press at the same time, during at least three seconds, the two buttons for disengaging the motor powered
rollers (Fig. 8J). The disengaging icon (Fig. 8P) will blink fast during these three seconds and every second
there will be a beep. This warns you that the system will be activated!
After these three seconds the motor powered rollers will be released from the tyre and the disengaging icon will
illuminate constant, now you can release the two buttons. When the motor powered rollers are completely
disengaged you hear a short beep, the disengaging icon will switch off and the system is ready for transport.
