Bedienungsanleitung Engenius EP 801 (Seite 23 von 152) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

458104

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

~45~

Call a Caller ID

When display a caller ID, Press or to dial

this number.

The displayed caller ID normally will be a 10-digit

number with a 3-digit area code followed by the 7-digit

telephone number.

The number in call log can be modified to comply with

the local dialing rules.

Press key, use or key to scrool the

call log.

To display the telephone number without “1” or area

code, press FORMAT (Left) soft key.

For example, the number stored in the call log is “1-

555-423-1234”, press the FORMAT (Left) soft key

once, the displayed number will be changed to “423-

1234”.

Press the FORMAT (Left) soft key a second time, it

will be changed to “555-423-1234”.

Press the FORMAT (Left) soft key a third time, it will

be changed to original number “1-555-423-1234”.

Press or to dial this displayed number which

complies with the dialing rules.

Note: Normally the standard format of telephone

number is 10-digit or 11-digit, if the number

doesn’t meet the format (For example, over 11-

digit), then the displayed number will not be

modified as above item 5 when press FORMAT

(Left) soft key.

Base Speed Dial Setting

You can store up to 20 entries in the speed dial memory. Each speed

dial memory can contain a phone number (up to 32 digits).

Base during standby mode, press key, enter the telephone

number.

Press key, followed by a 2-digit memory location, base then will

emit a two short tone (Bi-Bi) to confirm the setting.

~46~

Re: The memory location is “00” ~ “19”.

When using the base speed dail, press key followed by

key, then enter the 2-digit memory location (“00”~”19”).

The base will dial the telephone number accordingly.

Base Ringer Setting

You can change the base ringer by following :

Base during standby mode, press key twice, followed by

or key, the base speaker will emit the varied ringer (up to 8

ringer tones).

Press key to confirm the setting.

To adjust the ringer volume, two options can be followed:

a. Base during standby mode, press or key.

b. When incoming call, press or key.

c. When press or key to adjust the volume, the speaker will

emit the loudness of ringer, you can choose the preference.

Re: The loudness level of ringer is “0~4”, “0” means ringer “Off”.

Multi-Base Setting

“Multi-Base” setting allows expanding coverage or lining capacity. When

adding 2

, 3

or 4

base, using one of the handsets which registered to the

base (i.e. the handset with ID 11), followed by below processes：

Press MENU, followed by “7” to enter the registration

mode.

Press & hold the base REG button for thress seconds,

the base will emit the prompt ringing (also the base

speakerphone & Intercom LED is flashing).

Press digit “3” of handset to enter the Multi-Base

mode.

Select BS # 1

Repeat above step 1 ~ 4 to continuously add the 2

or 4

base.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Engenius EP 801 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Engenius EP 801

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info