Bedienungsanleitung Engenius EP800 (Seite 18 von 351) (Englisch)

619916

Zoom out

Zoom in

Vorherige Seite

1/351

Nächste Seite

~35~

To unlock the keypad, press UNLOCK (Left) soft key,

then, within 2 seconds, press the digit “＊” to unlock.

Once returning back to standby mode for 15 seconds,

the keyguard will be automatically enabled.

Key Guard is in effect until unlocked.

Battery Recharge and Replacement

1. Charge the battery when one or several of the following happen:

a. Phone beeps twice (every 60 seconds in talk mode, every 10

minutes in standby mode).

b. Battery icon is empty.

Phone does not respond when a power on/off key is pressed.

d. LCD and backlighting become dim.

e. Talk range shortfall is experienced.

You can replace the handset battery after placing the call-in-progress on

hold and press key. To retrieve the call on held, press talk key

again after replaced battery and power the handset on..

3. Battery talk time and standby time vary depending on the talk/standby

pattern and the operating distance. Putting the handset back to charger

cradle as often as possible is recommended for best performance. Use

only manufacturer provided battery and charger!

~36~

Advanced Operations

Handset Registration

1. If your handset(s) is purchased as part of a system, it has been pre-

registered with the base station at the factory.

2. If Handset ID as “00,” that means it is a new handset or the ID has been

erased. You need to register the handset with the base station.

Registration:

Press MENU-7 to enter the registration mode

Press and hold the base’s PAGE button for 3

seconds until the In Use LED (white color) lighting

up and flashing, also the base station will emit

prompt sound to remind you the base station is in

the registration mode..

Press handset key “1”, this completes the

registration process. The base station will assign a

handset ID between 12 and 19 automatically. The

assigned ID will be displayed on the handset LCD,

indicating successful registration.

Repeat above steps for all additional handsets.

De-registration:

You can de-register the handset you’re using from

the base station. De-registration will reset the

Handset ID to 00, erase the system security code,

and free up the handset ID for future registration.

After deregistration, the handset will not be able to

use the base station to make or receive phone

calls, nor can it intercom other handsets.

Press MENU-7 to enter the registration mode

Press and hold the base’s PAGE button for 3

seconds until the In Use LED (white color) lighting

up and flashing, also the base station will emit

prompt sound to remind you the base station is in

the de-registration mode.

Press the handset number key “2”, this completes

the de-registration process. Upon successful de-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Engenius EP800 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Engenius EP800

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info