Bedienungsanleitung Epson EB-1480Fi (Seite 31 von 319) (Englisch)

737384

Zoom out

Zoom in

Vorherige Seite

1/319

Nächste Seite

Projector Placement

Front Upside Down/Rear Upside Down (Vertically)

Select the correct Projection option in the projector's Installation menu

according to the installation method being used. If necessary, turn on the Inv

Direction Button setting in the projector's Operation menu and adjust the

Menu Rotation setting in the projector's Display menu.

• The default Projection setting is Front/Upside Down.

• You can change the Projection setting as follows by pressing down

the [A/V Mute] button on the remote control for about 5 seconds.

• Switch Front to/from Front/Upside Down

• Switch Rear to/from Rear/Upside Down

gg Related Links

• "Projection Modes" p.59

• "Changing the Projection Mode Using the Remote Control" p.59

• "Changing the Projection Mode Using the Menus" p.59

Settings when Using the Interactive Features

When using the interactive features, project from in front of the screen

(EB‑1485Fi/EB‑1480Fi).

Set Projection to Front/Upside Down or Front.

Attention

The interactive features are operated using infrared communication. Note the

following points when installing the projector.

• Do not install the projector tilted at an angle of 3˚ or more. The interactive

features may not operate correctly.

• Make sure there is no strong light or sunlight shining on the interactive pen

receiver, the projection screen, the projector itself, or the rear of the projector.

• Do not install the projector where it could be subjected to direct sunlight

through a window. This could cause the interactive features to malfunction.

• Install the projector so that the interactive pen receiver is not too close to

fluorescent lights. If the surrounding area is too bright, the interactive features

may not operate correctly.

• If there is any dust stuck to the interactive pen receiver, it could interfere with

infrared communication and the interactive features may not operate correctly.

Clean the receiver if it is dirty.

• Do not put paint or any stickers on the cover of the interactive pen receiver.

• When using the interactive features, do not use an infrared remote control or

microphone in the same room. The interactive pen could malfunction.

• Do not use devices that generate powerful noise, such as rotary devices or

transformers, near the projector, as the interactive features may not operate

correctly.

• We recommend using a smooth, board type screen without any

unevenness. If the projection screen is uneven, there may be

distortions in the projected image.

• Distortions may occur in the projected image depending on the

material of the screen and the installation method.

• When using the interactive features, install the projector so that the

projected screen is a rectangle without any distortion.

• When using the interactive features in the same room as multiple

projectors, interactive pen operations may become unstable. In this

case, connect the optional remote control cable set to the projectors,

and change Sync of Projectors to Wired in the projector's

Pen/Touch menu.

s Pen/Touch > Installation of Projectors > Sync of Projectors

gg Related Links

• "Settings when Using the Touch Unit" p.32

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson EB-1480Fi Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson EB-1480Fi

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info