Bedienungsanleitung Epson SureColor SC-S40600 (Seite 101 von 124) (Englisch)

617689

101

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

The print is not positioned properly

on the media.

Is the media loaded correctly and are the

margins correct?

If the media is not loaded correctly, the results may be

off center or part of the data may not be printed. You

should also check whether the correct options are

selected for Side Margin and Print Start Position in

the setup menu.

U “Loading media” on page 24

U “The Printer Setup Menu” on page 90

Is the media skewed?

If OFF is selected for Media Skew Check in the setup

menu, printing will continue when the media is

skewed and data will appear outside the print area.

Set Media Skew Check to ON in the Menu.

U “The Printer Setup Menu” on page 90

Is the media wide enough for the print data?

Although printing normally stops if the print image is

wider than the media, data will be printed beyond the

edges of the media if OFF is selected for Media Size

Check in the setup menu. Choose ON for Media Size

Check in the setup menu.

U “The Printer Setup Menu” on page 90

Vertical ruled lines are misaligned.

Is the media wavy?

Certain types of media may develop waves under

some conditions (humidity and temperature) while

installed in the printer. If a wave has developed, press

the d button in the control panel to feed the media

and avoid the affected area. We recommend that you

lower the temperature and humidity to prevent

waves developing.

Is the print head misaligned?

If the print head is misaligned, ruled lines may be

misaligned accordingly. In this case, select Media

Adjust - Head Alignment in the media settings to

adjust a print head misalignment that occurs during

printing.

U “Head Alignment” on page 45

Media

Media Jams.

Is media curled, folded, curved, creased, or

waved?

Cut and remove the curled, folded, curved, creased, or

waved part.

U “Cutting Media” on page 40

Is media loaded just before printing?

The pressure rollers may crease media left in the

printer, or the media may also become wavy or curled.

Is the media too thick or too thin?

❏ Check the media specifications to determine

whether it can be used in the printer.

U “Supported Media” on page 106

❏ For information on how to configure print

settings using the software RIP, contact the RIP

manufacturer.

Printing does not stop when the roll

ends.

Is the item for having the printer detect the

end of the media set to OFF?

When Media End Check is set to OFF from the Printer

Setup menu, the end of the media is not detected.

U “The Printer Setup Menu” on page 90

Removing Jammed Media.

Follow the steps below to remove jammed media.

Caution:

Be careful not to trap your hands or fingers when

opening or closing the front cover. Failure to observe

this precaution could result in injury.

Turn off the printer.

If a message is displayed and the printer will not

turn off, unplug both power cables.

SC-S60600 Series/SC-S40600 Series User's Guide

Problem Solver

101

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson SureColor SC-S40600 Seite 101

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson SureColor SC-S40600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info