Bedienungsanleitung Epson SureColor SC-S50600 (Seite 148 von 198) (Englisch)

617685

148

Zoom out

Zoom in

Vorherige Seite

1/198

Nächste Seite

Item Parameter Explanation

Media Tension 0 to 40 Increase tension if creases appear in the media during printing. The higher

the value, the greater the tension.

Media Suction 0 to 10

When media is waved on the platen, increase the Media Suction. The

higher the value, the greater the suction.

If graininess or out-of-focus characteristics are detected in printing results

obtained using thin or soft media or if the media is not fed normally,

reduce the Media Suction.

Head Movement

Data Width Choose the range in which the print head moves during printing.

Data Width restricts print head movement to the printed area. Restricting

the extent of print head movement increases print speed.

If Printer Full Width is selected, the print head will move the full width of

the largest media supported by the printer. Select this option for more

even print results with less variation.

Printer Full Width

Tension Measure-

ment

Periodically

Select Periodically or Every Page to automatically measure the media

tension and adjust to the optimal media feeding operation, or Off to

disable automatic tension adjustment.

Periodically is recommended in most circumstances.

Selecting Every Page enhances the accuracy of the Tension

Measurement for the optimal adjustment, but the printing time is longer

than when Periodically is selected.

The printer may however be unable to adjust tension appropriately for

some media, resulting in excessive slack or other maladjustments that

cause printing problems, in which case you should select Off. Note,

however, that Off may result in unusually large margin between pages. In

addition, after media has been ended, printing may not stop and the

inside of the printer may become stained. Observe the following

precautions:

❏ Do not print at the end of a roll.

❏ Do not set Media End Check in Printer Setup to Off.

Every Page

Off

Multi-Strike Print-

ing

Off Choose the number of times each line is printed.

To carry out high-density printing using backlight films, increase the

frequency.

2 to 8

Feed Speed

Auto

Auto is recommended in normal circumstances. If this option is set to

Auto, media is fed at the optimal speed depending on the number of

printing passes.

Select Lv1 for media that tends to stick together and for thin media that is

easily creased or torn.

Select Lv2 for faster printing. Note, however, that the feed speed will not

change if the number of passes is large.

Lv1

Lv2

Roll Type

Printable Side Out This option is set according to the setting that you selected when you

loaded the media.

Printable Side In

Restore Settings Yes

If Yes is selected, the setting content of selected media settings are

returned to the default settings.

EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide

Using the Control Panel Menu

148

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson SureColor SC-S50600 Seite 148

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson SureColor SC-S50600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info