Bedienungsanleitung Epson SureColor SC-S50600 (Seite 156 von 198) (Englisch)

617685

156

Zoom out

Zoom in

Vorherige Seite

1/198

Nächste Seite

Problem Solver

When a Message is Displayed

If one of the following messages is displayed, read and follow the instructions below.

Messages What to do

Prepare empty waste ink bottle. The waste ink bottle is getting full. Ready a new waste ink bottle.

U “Options and Consumable Products” on page 171

Ink Cartridge Error

Ink cartridge cannot be recognized. Insert

again or replace ink cartridge.

❏ Remove and reinsert the ink cartridge. If the message persists, insert a new

ink cartridge (do not reinsert the ink cartridge that caused the error).

❏ Remove and reinsert the replacement cartridge. If this message appears in

the control panel again, contact your dealer or Epson Support.

U “Replacement procedure” on page 118

❏ Condensation may have formed inside the cartridge. Leave it at room

temperature for at least four hours before installing the cleaning cartridge.

U “Notes on handling ink cartridges” on page 27

❏ When using a different type of Orange ink, see the following to change the

Orange ink.

UUsing Orange Ink (PDF)

Ink Cartridge Error

Ink cartridge cannot be detected. Insert

again or replace ink cartridge.

Ink Cartridge Error

Replace cleaning cartridge.

❏ Remove and reinsert the Cleaning cartridge. If the message persists, insert a

new Cleaning cartridge (do not reinsert the Cleaning cartridge that caused

the error).

U “Replacement procedure” on page 118

❏ Condensation may have formed inside the cartridge. Leave it at room

temperature for at least four hours before installing the cleaning cartridge.

Ink Low The ink is low. Ready a new ink cartridge.

U “Options and Consumable Products” on page 171

Warming Up...

Z Force to start printing

One or more heaters is still being warmed to the specified temperature. To start

printing without waiting for the heater to warm up, press the Z button.

Command Error

Check print settings on RIP.

❏ Press the W button and select Job Cancel. Check that the installed software

RIP is compatible with the printer.

❏ In the SC-S50600 series, if Platen Gap is set to 2.0 to make White ink printing,

this error message may be displayed.

Press the W button, and select Job Cancel to cancel printing.

Then, set Platen Gap to 1.5 or change RIP settings to make prints.

Print Data Error (MS)

Data containing MS cannot be printed if

printer is in 9 color mode.

This error message is displayed when print data using Metallic Silver is sent while

the color mode is set to 9 Color. Change to print data not using Metallic Silver, or

select Change Color Mode to change the color mode to 10 Color.

U “Change Color Mode (SC-S70600 series only)” on page 134

EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide

Problem Solver

156

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Epson SureColor SC-S50600 Seite 156

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Epson SureColor SC-S50600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info