Bedienungsanleitung Etna EN036V (Seite 7 von 16) (Deutsch, Englisch, Holländisch, Französisch)

2825

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

INSTALLATION

The appliance must be installed by qualified staff working in

accordance with the installation regulations in force.

Before installing, ensure that the appliance is correctly preset

for the local distribution conditions (gas type and pressure).

The presettings of this appliance are indicated on the label shown

on the cover.

This appliance is not connected to a flue gas extractor device.

It must be installed and connected in accordance with the

regulations in force. This appliance may only be installed and

operate in rooms permanently ventilated in accordance with

national regulations in force.

ROOM VENTILATION

The rooms in which gas appliances are installed must be well

ventilated in order to allow correct gas combustion and

ventilation.

The airflow necessary for combustion is at least 2 m

/h for each

kW of rated power.

POSITIONING (fig. 3)

Remove the hob from the packaging accessories, including the

films covering the chrome-plated and stainless steel parts. Place

the hob well away from items of furniture with sides higher than

the built-in hob. In addition, any separating wall parallel to the

work surface must be at least 1 cm below the hob casing, and

an opening 10 cm square must be provided underneath the gas

hose elbow. You are advised to make the gas connection before

positioning the hob in the supporting unit.

FIXING

A self-adhesive gasket (A) is supplied with the hob, and must

be placed under the edge of the box unit, as close as possible

to the edge itself (fig. 4). The gasket must fit all the way round

for a perfect seal, preventing moisture from getting beneath the

hob. Place the appliance in the hole in the hob, making sure

that the adhesive gasket provides a firm seal between the edge

of the hob and the surface of the unit (fig. 5), and adjust the

hooks already inserted in the casing (fig. 6).

CONNECTING TO THE GAS SUPPLY

Before connecting the hob, check that it is preset for the gas to

be used. The connection to the appliance is made on the left. If

other heating devices nearby mean there is a risk the hose may

overheat to above 30°C (e.g. if the line passes above another

appliance) a rigid pipe must be used.

Use of a rigid pipe (fig. 7) is compulsory for operation with natural

gas.

CONNECTING TO THE ELECTRICAL MAINS

Before making the connection, check that:

- the mains voltage is as indicated on the nameplate

- the earth connection is in good working order.

If the socket is not easily accessible, the installation engineer

must provide a switch with contact breaking gap of 3 mm or

more.

If the appliance power lead is not fitted with a plug, use an

approved standard type, remembering that:

- the green-yellow wire must be used for the earth connection;

- the blue wire is the neutral;

- the brown wire is live;

- the lead must never touch hot surfaces over 75°C;

- replacement leads must be of type H05RR-F or H05V2V2-F

of suitable size (see fig. 2) for gas and all-electric appliances,

and of type FR3R3 of suitable size (see fig. 2) for mixed

appliances;

- the power supply lead must only be replaced by a qualified

technician.

IMPORTANT: the manufacturer declines all liability for damage

due to failure to comply with the regulations and standards in

force.

Check that the appliance is correctly connected to the earth (see

fig. 2).

FOR HOBS WITH ELECTRIC IGNITION

The correct gap between the electrode and the burner is shown

in figure 9.

If no spark is generated, do not keep on trying as this might

damage the generator. Possible causes of malfunction:

- spark plug damp, dirty or broken;

- electrode-burner gap not correct;

- spark plug wire broken or without sheathing;

- spark discharging to earth (to other parts of the hob);

- generator or microswitch damaged;

- air has built up in the pipes (particularly if the hob has been out

of use for a long time),

- air-gas mixture incorrect (poor fuel setting).

IMPORTANT

- Before carrying out any work inside the appliance, disconnect

the mains plug and shut off the gas tap.

- Never use matches to check for gas circuit for leaks. If a specific

control device is not available, foam or very soapy water can

be used.

- When re-closing the hob, check that the electric wires of the

spark plugs (if present) are not close to the injectors, so that

they cannot run across them.

GB Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Etna EN036V Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info