Bedienungsanleitung Eufy T2151 - RoboVac G10 Hybrid (Seite 23 von 24) (Englisch)

783788

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

42 43

- You are using a 2.4GHz router or a dual-band router that is configured to support a

2.4GHz frequency band. RoboVac does not support 5GHz frequency band.

- If RoboVac cannot connect to the Wi-Fi network and you are using a 2.4/5GHz

mixed network, switch to a 2.4GHz network for Wi-Fi setup. You can switch back

once your setup is complete.

- When connecting to a hidden network, make sure you enter the correct network

name, SSID (case sensitive), and connecting to a 2.4GHz wireless network.

- When using a network extender/repeater, make sure the network name (SSID)

and password are the same as your primary network.

- The firewall and port settings of your Wi-Fi router allow RoboVac to connect with

the Eufy servers.

Network Security Requirement

- WPA and WPA2 using TKIP, PSK, AES/CCMP encryption.

Wi-Fi Channels

- The FCC requires that all wireless devices in the United States operate on the 1-11

wireless spectrum channels.

- Some countries outside North America can use spectrum channels higher than

channel 11. Refer to your local regulatory agency to determine which channels are

accessible.

- A future software release will support access to channels above 11 for users

outside North America. Until then, use channels 1-11.

If you cannot control RoboVac with your smartphone, try the solutions below to solve

the problem. If the problem persists, contact the Eufy service center for help.

Wi-Fi Status

Light Cause Solutions

Solid blue

RoboVac has connected

to your router, but

cannot access the

Internet.

• Check if your router is connected to the

Internet.

• Check with your Internet provider to

see if there is any Internet connection

problem.

Rapidly

flashing blue

RoboVac cannot

connect to your

wireless router.

• Check if you have modified your network

name and password.

• Reset Wi-Fi connection if necessary.

Refer to the “Use Your RoboVac with

the EufyHome App > Restore Factory

Settings” section in this manual.

Slowly

flashing blue

Wi-Fi connection is

reset or has not been

set up before.

• Set up Wi-Fi connection with RoboVac.

Refer to the “Use Your RoboVac with

the EufyHome App” section in this

manual.

• Reset Wi-Fi connection if necessary.

Refer to the “Use Your RoboVac with

the EufyHome App > Restore Factory

Settings” section in this manual.

Wi-Fi Status

Light Cause Solutions

Off

• RoboVac is turned off.

• RoboVac’s power

level is low.

• RoboVac is in Sleep

mode.

• Charge RoboVac by attaching it to the

Charging Base. Make sure the main

power switch on the bottom of RoboVac

is turned on.

Specifications

Input 19 V 0.6 A

Battery Voltage 14.4 V

Power Consumption 40 W

Battery Type 14.4 V

Li-ion 2600 mAh

Dust Collector Capacity

450 ml

Water Tank Capacity 130 ml

Charging Time 300 - 360 mins

Input 19 V 0.6 A

Output 19 V 0.6 A

Customer Service

For FAQs and more information, please visit www.eufylife.com.

Email: support@eufylife.com

Live Chat: www.eufylife.com

Anker Innovations Limited

Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eufy T2151 - RoboVac G10 Hybrid Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Eufy T2151 - RoboVac G10 Hybrid

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info