Bedienungsanleitung Eurom BK2003 (Seite 13 von 20) (Deutsch, Englisch, Holländisch, Französisch)

474865

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

1= large screw

2 = attachment bracket

3 = plug

4 = small screw

5 = screw holes

Set-up and Operation

 Check if the mode selector dial is set to 'OFF' (O).

 Fully extend the power cord and plug into a suitable 220-240V socket. To prevent the circuit overloading,

check that no other appliances are connected to the same group.

 Switch the heater on by turning the mode selector dial to one of three positions; The pilot-light will turn on.

Fan only (thermostat to maximum)

I Heating at half power (1000W)

II Heating at full power (2000W)

It is most economical to heat the space at full power, then to switch to half power to maintain the

temperature.

 Both at half and full power, the fan rotates at the same speed; the difference between the two lies in the

number of heating elements in use.

 The thermostat serves to maintain a constant room temperature. To set the desired temperature, turn the

thermostat dial to its maximum position (clockwise as far as it goes). Set the mode selector dial to I or II.

Once the desired temperature is reached, turn the thermostat dial back slowly until you hear a click. This

causes the heater to switch off. The heater will now automatically switch on and off to maintain the set

temperature.

 To switch the heater off, set the power dial to ‘0’ (off). Unplug.

Safety features

The heater is fitted with a tipping safeguard which automatically shuts off the appliance if it inadvertently falls

over. When the heater is returned to its upright position, it will resume functioning as normal but, before reusing,

switch off, unplug and check for damage. Do not use the heater if it is damaged or malfunctioning, but have it

inspected/repaired!

In case of internal overheating, the overheating safeguard will switch the heater off. This may occur if the heater

cannot give off enough heat or if it cannot draw in enough fresh air. As mentioned above, this is generally caused

by (partially) covering the heater, obstructing the air intake and/or outlet grills or installing the heater too close to a

wall or something similar. When the overheating safeguard switches the heater off, set the mode selector dial to

‘0’ (off), unplug and allow the heater to cool down. Remove and/or amend the cause of overheating and reuse the

heater as normal. If you cannot find a cause and overheating recurs, stop using the heater, and take it in for

inspection/repair.

Cleaning and Maintenance

Keep the heater clean. Deposits of dust and dirt in the appliance are a common cause of overheating so these

should be removed regularly. Switch off the heater, remove the plug from the socket and allow the heater to cool

down before cleaning or carrying out maintenance work.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eurom BK2003 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info