Bedienungsanleitung Eurom PH2750 met CO2-detectie (Seite 28 von 48) (Deutsch, Englisch, Holländisch, Französisch)

591484

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

PH2750C

Type PH2750C is fitted with an air sensor: a device that immediately measures the CO²

(carbon monoxide) in the room. This device will also automatically de-activate the heater if

you use the heater under abnormal conditions (poor ventilation or an insufficiently large

room).

If this occurs, do not try to reactivate your heater immediately. First ventilate thoroughly,

refresh the air and wait until the temperature in the room drops. Remove the cause of the de-

activation before using the heater again.

In this embodiment (PH2750C) is the flame height not adjustable.

A. THE INSTALLATION OF THE HEATER

1. UNPACKING

1. Open the cardboard packaging.

2. Take the heater and its accessories out of the box and remove the filler pieces on the

sides.

3. Open the protective grill (4 in diagram A) by holding it on the right side, lifting it and then

pulling it forwards. Take the burner out of the heater by first sliding the top cardboard filler

piece down and then removing it and then removing the bottom filler piece.

4. Put the burner back in place and ensure that it is positioned correctly. To do this, move

the metal spring that is fastened

under the burner back and forth

a few centimetres until the

burner is in the correct position

(diagram B).

5. Put the protective grill

back in position. Place the

vertical right in the top opening,

lift it up, push it and then allow it

to drop into the bottom opening.

6. Open the cover that provides access to the fuel tank (2 in diagram A) and remove the

filler piece that is under the cover.

7. Put all of the packaging components that you have removed back into the box and store

this in a dry place during the season when the heater

is in use.

8. Remove the screw from the cover of the battery

compartment on the back of the heater. Push the

cover upwards and pull it forward. Now place the

alkaline batteries (PH2750: 2 x D, 1,5V – PH2750C:

4 x R14, 1,5V) with the + and – poles as indicated.

Now close the cover again (Diagram C) and screw it

closed. Remove the batteries from the heater if they

are not being used for an extended period of time.

9. Check the de-activation system in the following way:

- Move the wick to the highest position with the aid of

the appropriate button (7 in diagram A).

Attention: This is not possible when the tank has been removed. This heater was

designed for temporary use – the heater will not work if the tank is absent.

- press the stop button (8 in diagram A) in order to move the wick down again.

In order to ascertain that the wick has moved completely to the lowest position again, try

to turn the button (7 in diagram A) anti-clockwise. If this is not possible, this means that

the de-activation system is functioning correctly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eurom PH2750 met CO2-detectie Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info