Bedienungsanleitung Eurom PH2750 met CO2-detectie (Seite 29 von 48) (Deutsch, Englisch, Holländisch, Französisch)

591484

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

If you are able to turn this button anti-clockwise, the de-activation system is defective.

You are then not permitted to use the heater or to attempt to resolve this problem. You

must contact the customer service department.

Attention! Danger!

 Never remove the batteries while the heater is in operation.

 Ensure that good quality alkaline batteries are used

 Never ignite the heater with a match, a lighter or any other flame

whatsoever.

B. FILLING THE FUEL TANK

Due to fire safety considerations the fuel tank must be filled in the following manner:

- First, switch the heater off.

- Fill the tank in a different location to the heater.

- In all cases you must check that the refilled tank is correctly sealed and is located at a

safe distance from any heat sources or open flames.

1. Use the handle to pull the fuel tank out of the

heater (diagram D).

2. Open the fuel packaging and insert the straight

suction line of the siphon pump into it (1 in diagram

E).

3. Place the fuel tank with the screw top facing up

next to the fuel packaging, with the handle folded

down. Ensure that the tank is completely stable or

hold it firmly so that it cannot fall over. Now

unscrew the cap of the fuel tank.

4. Insert the flexible, ribbed hose of the siphon pump

(4 in diagram E) into the tank.

5. Pump the fuel from the packaging into the tank by

squeezing the bellows of the pump (2 in diagram

E). The sealing plug of the bellows (3 in diagram E)

must be in the “ON” (closed) position.

6. Monitor the fuel level in the tank. This level can be

seen in the window on the top of the tank (diagram

F).

As soon as this window starts to change from

yellow (1 in diagram F) to black (2 in diagram F),

you must move the sealing plug to the “OFF”

position (therefore unscrewing it a little) and wait

until the pump is empty before you remove it. If the

window is completely black, the tank is too full (3 in diagram F).

Attention: avoid spillage. If this does occur, clean the tank thoroughly before putting it

back into the heater.

7. Put the cap back on to the fuel tank and place the tank back into the heater. The

window of the fuel tank is now located at the bottom of the heater. You can see this

window through the housing of the heater. It is black (1 in diagram G), and when it

changes to yellow (2 in diagram G) this means that there is only a small quantity of

fuel remaining and that you must refill the tank. When the window changes to

completely yellow (3 in diagram G) the tank is completely empty.

ATTENTION: Check that the heater is switched off and cool before refilling the tank. You are

only permitted to remove the tank from the heater when this is the case. This prevents the

possibility of accidents caused by droplets falling onto the heater.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eurom PH2750 met CO2-detectie Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info