Bedienungsanleitung Eurom PH2750 met CO2-detectie (Seite 31 von 48) (Deutsch, Englisch, Holländisch, Französisch)

591484

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

If the wick is abnormally hard or blocked or burns abnormally it must be replaced by an

appropriately qualified professional. Ask your supplier.

The wick and its replacement are not covered by the guarantee. Therefore follow the

instructions for use closely in order to ensure maximum performance.

A non-original wick that does not have the correct properties or is incorrectly adjusted can

have a negative effect on the combustion process, with the risk of de-activation or carbon

monoxide poisoning. Your heater will then no longer meet the requirements!

The guarantee lapses when a wick other than an original wick is used.

E. IGNITION

Before igniting the heater, check that:

- the heater is stable and horizontal

- there are not object located within 1 metre of the heater

- the correct batteries (4 x LR14) are in place

- the burner is in the correct position over the wick

- the tank contains a sufficient quantity of the correct fuel

- all other circumstances are safe

For your convenience and safety, this heater is fitted with an ignition system that is powered

by the four batteries that you have already placed in the battery compartment of the heater.

ATTENTION: when using this heater for the first time you must for two hours after placing

the tank before igniting the heater. The wick must be thoroughly saturated with fuel.

We recommend that you ignite the heater outside when you first use it because certain parts

of the heater are coated with grease in the factory and this must burn off.

If you want to test the heater during a warm season you may experience problems with

ignition. A temperature-sensitive safety feature is linked to the wick mechanism. When the

ambient temperature exceeds 25°C it is no longer possible to ignite the heater. Wait until the

temperature drops or carry the test out after the heater has been cool for some time (out of

drafts).

Ignition:

1. Turn the adjustment knob for the wick height (7 in diagram A)

clockwise until the wick is at its highest position.

2. Press the ignition button (6 in diagram A) so that the igniter

makes contact with the wick.

3. As soon as the wick is lit (normally after 1 or 2 seconds),

release the button. The spiral filament will then drop down. Do

not depress the button for too long, in order to prevent the wick

from burning. If the wick does not ignite, try again after 10 to

15 seconds.

4. If necessary, move the metal spring that is fitted under the

burner back and forth a little (see diagram B) so that the

burner moves into the correct position.

5. Check the flames after the heater has been lit for 5 to 7 minutes. The flames must be red

and evenly distributed across the entire length of the burner (see diagram I). If this is not

the case, move the spring fitted under the burner carefully back and forth (see diagram

B).

WARNING: never ignite your heater with a match, lighter or other fire!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eurom PH2750 met CO2-detectie Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info