Bedienungsanleitung Eva Calor Hydro Slim 16 kW (Seite 27 von 55) (Englisch)

668834

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

Second phase. Ignition

After the preparation phase, the display will show the message "LOAD PELLETS" and ignition

will begin. This second phase is divided in two parts: pre-loading and actual ignition. First, the pellet

feed screw is activated (the Feed screw ON LED lights up) for a variable time interval,

depending on the model, and pellets begin to fall inside the brazier. (Remember that the brazier

must be perfectly clean at this beginning of this stage). Once this "pre-loading" phase is

completed, the pellet feed screw will stop for a variable amount of time depending on the model

(from two to three minutes). After this waiting phase, the pellet feed screw will start to switch on at

regular intervals and pellets will then continue falling inside the stove brazier, while the glow plug

and then fume exhaust fan will both remain activated.

As soon as the pellets cover the glow plug hole, you will notice first a reddening and then the

onset of a small flame in the brazier.

If pellets continue to fill the brazier without this happening, manually stop the ignition process

without waiting for the stove to set off an alarm: "AL 5 NO START".

This second phase is completed when the stove detects successful triggering of the combustion

process, or rather after 4-5 minutes from the triggering of the first flame.

If combustion is not detected within a given amount of time, the no start-up alarm will be activated

("AL 5 NO START" message).

Third phase. Stabilisation

Once combustion triggering has been detected, the third phase will start and the display will show

the message "FIRE PRESENT". Pellet feeding is reduced and ventilation increased in order to

allow a stabilisation of the flame and disposal of excess pellets accumulated in the brazier during

the ignition phase. This phase lasts about 5 minutes.

Once the stabilisation phase has been completed ("FIRE PRESENT"), the stove passes to the

normal working phase.

6.3.2 No start-up

As said, if the onset of combustion is not detected, the no start-up alarm will be set off. The display

will show the message "AL 5 NO START" and an acoustic signal will be heard at regular intervals

(if the buzzer function is active in Menu 6).

To disable the alarm, hold and press the ON-OFF (4) (about 2 secondi) . The acoustic alarm

will stop and the stove will return to "FINAL CLEANING" status and then to "OFF."

Before starting another ignition cycle:

- Verify the cause of the alarm.

In particular:

 Verify that the pellet tank is not empty.

 Verify that the brazier is in the right position.

 Remove the unburned pellets from the brazier (VERY IMPORTANT).

If the device does not ignite regularly, the main cause may be insufficient maintenance or poor

pellet quality.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eva Calor Hydro Slim 16 kW Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info