Bedienungsanleitung Eva Calor Hydro Slim 16 kW (Seite 29 von 55) (Englisch)

668834

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

- View water circuit pressure. Press and hold button 5.

Periodic brazier cleaning is also active during working mode. Brazier cleaning mode is activated

at regular intervals of about one hour. In this way, the smoke extractor works at maximum power

while pellet feeding is reduced to minimum. This operation is necessary for eliminating ash deposits

inside the brazier and for ensuring proper aeration and combustion. During brazier cleaning, the

display will show the message "BRAZIER CLEANING". If you notice excessive accumulation of

pellets in the brazier during normal operation, turn off the stove immediately and contact a

service centre. Forcing could make your stove a hazard.

6.3.4 Modulation based on room temperature (all models)

The stove is equipped with an internal temperature sensor that allows it to modulate its power

according to the desired room temperature.

For correct environment sensor operation, verify that the thermostat sensor positioned in the rear

of the stove under the outlet (see Figure 14) is away from the fume exhaust pipe and is not in

contact with objects or walls.

Press button "2" to set room temperature. The message " SET ROOM TEMP" will appear on the

bottom of the display, while the upper part will show the set temperature.

To modify this value, use buttons "1" and "2" until you reach desired temperature (7°C to 40°C).

If the room temperature reaches the set temperature, the stove goes into minimum power and

the last line of the display shows "MODULATE." This modulation has been completed only if the

room temperature returns to being lower than the set temperature. In this case, the stove will return

to the power set by the user and the display will show the message "MODULATE" and standard

working indications will return.

6.3.5 Modulation based on boiler water temperature (Hydro stoves and

boilers only)

The stove is equipped with boiler water temperature sensor that allows it to modulate its power

according to the desired temperature.

To set water temperature, press button "1". Press button "1" once and the bottom of the display

will show the message " SET WATER TEMP", while the upper part of the display will show the set

water temperature. To modify this value, use buttons "1" and "2" until you reach desired

temperature (30°C to 80°C). We recommend setting water temperature in the boiler between

60° C and 70° C.

Briefly press button "4" to exit from programming or wait a few seconds to automatically return to

the work or stand-by position.

During the working phase, if the water temperature in the boiler is much lower than the set value,

the stove operates at the maximum power level set.

However, when the boiler water temperature approaches the set value (difference of less than 3°

C), the stove heater gradually decrements the power level. The last line of the display shows a

flashing number that indicates the power level at which the stove is working at that moment. A

decrease in water temperature will correspond to an increase of the power level until it returns to

the maximum power value set initially. We recommend always setting Hydro stove power to its

maximum value "5".

If, despite reducing power, boiler water temperature continues to rise and reaches the set

temperature, the bottom line of the display will show "MODULATE." If, despite modulation, the

water temperature tends to rise further (for example when zone valves are closed), it may be best

to activate stand-by mode (see section 7.5).

6.3.6 Ventilation (air and channelled air models)

Air models provide ventilation which diffuses the heat generated from by the stove into the

surrounding environment. Activation of the ventilation occurs based on the temperature of fumes.

Therefore, it starts up after ignition and switches off with a delay compared to stove shutdown.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eva Calor Hydro Slim 16 kW Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info