Bedienungsanleitung Everdure Force (Seite 8 von 13) (Englisch)

798845

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

1514 Assembly, Operation & Maintenance InstructionsAssembly, Operation & Maintenance Instructions

STEP 01

/ The hood and barbeque chassis assembly is transported screwed to the stand top by

four M6x20mm screws and four Ø6mm spring washers (two at the front and two at the

rear). Before attempting to build the stand, the stand top should be removed.

Angle the assembly slightly to the back and remove both M6x20mm screws, then do the

same at the front, supporting the parts so they don’t drop. Keep all of the fasteners for

later use. Removable stickers at the front and rear will mark the positions of these screws.

Remove the hood and barbeque chassis assembly from the stand top and place on the

ground.

STEP 02

/ Take the stand top (01B) and place it upside down (leg stumps up) on a clean surface

(note: there is no front or rear to this part). Take the right front leg (04 with a screw hole

in the foot) and slot it over the rear right corner stump. Fix in place using a M6 x 12mm

screw (A) and spring washer (D), but do not tighten. Take the right rear leg (05 with a

screw hole in the foot) and slot it over the front right corner stump. Fix in place using a

M6 x 12mm screw (A) and spring washer (D), but do not tighten.

Take the left front leg (02) and slot it over the rear left leg stump. Fix into place using a

M6x12mm screw (A) and spring washer (D), but do not tighten. Take the left rear leg (03)

and slot it over the front right leg stump. Fix into place using a M6x12mm screw (A) and

spring washer (D), but do not tighten.

STEP 03

/ Take the two bottom shelf supports (06) and t them onto the cylindrical tabs at the

inside of each foot. Rotate each one so that the outmost screw holes are facing inwards

and the inner screw holes are facing the stand top (if not, pull out and t in the opposite

way). Fix in place with four M6x12mm screws (A) and spring washers (D). When all are

assembled, tighten up all four screws and the screws from step 02.

STEP 04

/There are two threaded holes at the inside of the right hand legs. Take the support chain

(15) and x it to the two legs with two M6x12mm screws (A). Tighten fully.

STEP 05

/ Turn the stand onto its legs and check that all of the legs are stable. Take the plastic

bottom shelf (07) and place it on the two bottom shelf supports. Line the four holes in

the bottom shelf up with the threaded holes in the bottom tray supports and x into

position using four M5x12mm screws (B) and four spring washers (E). Tighten fully.

STEP 06

/ Push the at edge of the cylinder hook (14) into the slot of the stand top (above the

right hand side legs and castors) up until the dogleg, and then rotate down until the hook

is against the stand top side. Fix into place using a M6x12mm screw (A), M6 locking nut

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Everdure Force Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info