Bedienungsanleitung Exquisit GE 9106.1 T (Seite 3 von 58) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

717898

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Gas Connection and Security

1. Before your appliance is connected to the gas supply, ensure that the gas category and pressure

specifications shown in the data plate corresponds with your gas supply. If necessary call authorized

service for adjusting to gas category.

2. This appliance shall be installed in accordance with the regulations in force and only used in a well

ventilated space. Read the instructions before installing or using this appliance. In the interest of safety this

appliances must be installed and / or serviced by a competent person as stated in the gas safety regulations

current editions.

3. The appliance must not be installed in a room without a window or other controllable opening. If is

installed in a room without a door which opens directly to the outside, a permanent opening is required.

The air circulation should be 2 m3/h per kW of burners.

4. The gas connection should be performed from the right or left. For this reason, change the hose nozzle,

plug and the seals.

5. Please use flexible hose for gas connection.

6. If you make a connection with a flexible metal hose, locate a seal between the main gas pipes.

7. The inner diameter of the flexible hose, which the butane hose nozzle is connected, should be 6mm for the

house-type gas tubes. The inner diameter of the flexible hose, which the natural hose nozzle is connected,

should be 15mm.The hose should tightly be fitted to the hose nozzle by squeezing with a clamp. The hose

should be replaced before its last expiry date.

8. Caution! Make the oven connection to the gas inlet valve, the hose length must be short and be sure that

there is no leakage. The flexible hose used should not be longer than 125 cm for safety.

9. RE-INSPECT THE GAS CONNECTION.

10. When placing your oven to its location, ensure that it is at the counter level. Bring it to the counter level by

adjusting the feet if necessary.

DO NOT MAKE GAS HOSE and ELECTRICAL CABLE OF YOUR OVEN GO THROUGH THE HEATED

AREAS, ESPECIALLY THROUGH THE REAR SIDE OF THE OVEN. DO NOT MOVE GAS

CONNECTED OVEN. SINCE THE FORCING SHALL LOOSEN THE HOSE, GAS LEAKAGE MAY

OCCUR.

INSTALLATION OF THE OVEN FEET

In order to install the oven feet;

1. Foot attachment lath is installed on the oven from the bottom of the oven as shown in Figure 1. Nuts are

centered on these lathes in order to screw feet (Figure 2). Complete the feet installation process by

screwing the feet to the nuts (Figure 3).

2. You can balance your oven by turning the screwed feet according to the surface type you are using.

3. If your oven has plastic food as in Figure-4 you can adjust your ovens height from these feet as turned

clockwise or anticlockwise.

Figure 1 Figure 2 Figure 3 Figure 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Exquisit GE 9106.1 T Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info