Bedienungsanleitung Extraflame Fiandra Idro (Seite 27 von 36) (Englisch)

695872

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

27ENGLISH

AUX

If the producer's conveyed wave accessories are used, the connection must be made by the qualied technician directly in the board.

Contact the dealer for further details

LCD HANDHELD REMOTE ROOM PROBE CALIBRATION

This mode allows calibration of the room temperature detected by the LCD handheld remote (with ventilation active only). For correct

calibration, it is recommended to position the LCD handheld remote in a room with constant temperature and wait for at least two hours.

Below nd the calibration procedure:

 Access the menu and reach “TECH MENU”.

 Set the access key "F4". - "ADJ REMOTE PROBE"

 Use the

keys to adjust the desired room calibration.

 Save and exit via the

key.

ADDITIONAL THERMOSTAT

N.B. : Installation must be performed by an authorised technician

It is possible to thermostat a room adjacent to the room where the stove is positioned: just connect a thermostat following the procedure

described in the next step (it is recommended to position the optional mechanical thermostat at a height of 1.50 m from the oor) . Stove

operation with external thermostat connected in the clamp TA can be dierent on the basis of activation or deactivation of the STAND

BYfunction.

By default, the clamp TA exits jumpered, therefore it always has closed contact (on request).

ADDITIONAL THERMOSTAT FUNCTIONING WITH STANDBY ACTIVE

When the function is activated, STBY will be shown on the display. When the contact or external thermostat is not satised (open contact

=temperature reached), the stove will switch o. As soon as the contact or external thermostat switches to the "not satised" status (closed

contact / temperature to be reached) it will re-ignite.

Nota bene: stove operation depends on the temperature of the water inside the stove and relative factory setting restrictions. If stove

is in HOFF (water temperature reached), any additional contact or thermostat request will be ignored.

ADDITIONAL THERMOSTAT OPERATION WITH STANDBY DEACTIVATED

When the contact or external thermostat is satised (open contact / temperature reached), the stove will go to minimum. As soon as the contact

or external thermostat switches to the "not satised" status (closed contact / temperature to be reached) it will start to work again at the pre-set

power.

Nota bene: stove operation depends on the temperature of the water inside the stove and relative factory setting restrictions. If stove

is in HOFF (water temperature reached), any additional contact or thermostat request will be ignored.

ADDITIONAL FUNCTIONS

ADDITIONAL THERMOSTAT INSTALLATION

 Switch the appliance o using the master switch positioned on

the rear of the stove.

 Remove the plug from the socket.

 Connect the two cables of the thermostat to clamp (TA),

positioned on the rear of the machine.

DEPRESSURE NOTICE

It allows to activate the warning buzzer if the door or hopper is open.

Please note: activating this buzzer may reduce battery life by 30%.

Battery life depends on use.

To set: OK>SETTINGS>DEPRESSURE NOTICE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Fiandra Idro Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Fiandra Idro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info