Bedienungsanleitung Extraflame Isidora Idro H16 (Seite 25 von 40) (Englisch)

811756

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

25ENGLISH

EASY SETUP

The volumetric weight of the pellet is the ratio between the weight and the volume of the pellet. This ratio may change while keeping the

quality of the pellet unchanged. By using the EASY SETUP function, it is possible to dose the pellets by increasing or decreasing the preset

values.

In the stove program, the available values go from “– 3” to “+ 3”; all stoves are calibrated during production with the optimal value which is 0

If you notice an excessive deposit on the burning pot, access the EASY SETUP program and lower the value to “- 1”; then wait until the next

day and if there is no improvement, decrease again, to a maximum of “- 3”.

If, on the other hand, it is necessary to increase the pellet dosage, switch the factory value from "0" to "+ 1, + 2, + 3" as required.

EXCESSIVE PELLET DEPOSIT IN BURN POT NORMAL OPERATION MINIMUM PELLET DEPOSIT IN BURN POT

-3 -2 -1 0 +1 +2 +3

THIRD

DECREASE

RANGE IF THE

FIRST TWO ARE

INSUFFICIENT

SECOND

DECREASE

RANGE IF

THE FIRST IS

INSUFFICIENT

FIRST DECREASE

RANGE (TEST

FOR 1 DAY)

OPTIMAL FACTORY

VALUE

FIRST INCREASE

RANGE

SECOND

INCREASE

RANGE IF

THE FIRST IS

INSUFFICIENT

THIRD INCREASE

RANGE IF THE

FIRST TWO ARE

INSUFFICIENT

CONTROLS PROCEDURE

Press key 6.

Press key 3 until EASY SETUP appears and conrm by pressing key 6.

Use keys 4 -5 to set the range.

Press key 6 to conrm and key 1 to scroll back through the menus until the initial page.

N.B.: IF THESE ADJUSTMENTS DO NOT SOLVE THE PROBLEM OF PELLET DEPOSITS IN THE BURN POT, PLEASE CONTACT YOUR

LOCAL SERVICE CENTRE.

VENTILATION

The menu allows you to enable and adjust the speed (-2, -1, 0, +1, +2) of the front fan.

To ensure combustion eciency, the front air is excluded when the product is at the minimum power.

ENABLING CONTROLS PROCEDURE

Press key 6.

Press 3 until VENTILATION appears and conrm by pressing 6.

Conrm ENABLING by pressing 6.

Use keys 4 -5 to enable (ON) or disable (OFF) and conrm by pressing 6.

Press 1 to return to the previous menus to the initial state.

SPEED ADJUSTMENT CONTROLS PROCEDURE

Press key 6.

Press 3 until VENTILATION appears and conrm by pressing 6.

Keep pressing key 3 until SPEED appears and conrm by pressing key 6.

Use keys 4 -5 to adjust the speed (-2, -1, 0, +1, +2) and conrm by pressing 6.

Press 1 to return to the previous menus to the initial state.

SET THERMOSTAT CONTROLS PROCEDURE

Press key 6.

Press 3 until VENTILATION appears and conrm by pressing key 6.

Keep pressing 3 until SET THERMOSTAT appears and conrm by pressing 6.

Use keys 4 5 to adjust the room temperature (7°C - 37°C) and conrm by pressing 6.

Press 1 to return to the previous menus to the initial state.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Isidora Idro H16 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Isidora Idro H16

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info