Bedienungsanleitung Extraflame Terry plus (Seite 22 von 40) (Englisch)

696239

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

22 ENGLISH

IGNITION

After checking the previous points, press the key

for three seconds to switch on the stove. For the ignition phase, 15 minutes are available

during which the presence of the ame is checked. Once the control temperature has been reached, the stove stops the ignition phase and

goes into PREPARATION.

PREPARATION

During the preparation phase, the stove stabilises and gradually increases combustion, and then activates the ventilation and goes into

WORK.

WORK

During the work phase, the stove reaches the POWER dened by the user, heating the room until the SET THERMOSTAT has been reached.

See following note.

ADJUSTING THE SET THERMOSTAT

The SET ROOM THERMOSTAT can be set using keys 2 and 3, from LOWTA 7 - 37 °C - HOT. If the value is between 7 - 37°C, the stove checks

the room temperature using a probe in the remote control. Once the set temperature has been reached, the stove automatically reduces the

power ensuring optimal comfort and reducing the consumption of pellets: this process is called "modulation".

LOWTA  HOT

If the SET THERMOSTAT is "LOWTA" (set below the 7° threshold) the temperature is checked by the additional thermostat contact, thus

ignoring the temperature probe in the remote control.

If the contact is open (met), the stove operates at the minimum value.

If the contact is closed (required), the stove operates at the set power.

If the setting is on “HOT” (set above 37°C) the stove always operates at the set power, ignoring the external contact and the temperature probe.

ADJUSTING THE POWER

The power has 5 levels of operation, Pressing the key

allows you to view the set power which can be changed using the keys

Power 1 = minimum level - Power 5 = maximum level.

The change is conrmed by pressing the key

AUTO BLOW

During the work phase and at regular time intervals, the stove cleans the burn pot by means of an operation called "AUTO BLOW".

The activation of this function is shown on the display with the relative message. During the "AUTO BLOW" the pellet loading is slowed down

and the fumes motor is increased.

After the cleaning phase, the stove goes back to the normal operating conditions.

SWITCHOFF

Press the key

for three seconds.

After performing this operation, the appliance automatically enters the switch-o phase, and stops loading pellets.

The fumes motor and the hot air fan motor remain on until the stove temperature falls below the safety threshold.

REIGNITION

The stove can be switched back on only if the fume temperature is lower than a preset threshold and if a minimum safety time has elapsed.

OPERATION AND LOGIC

NO IGNITION

THE FIRST IGNITION MAY FAIL, SINCE THE AUGER IS EMPTY AND IT IS NOT ALWAYS POSSIBLE TO FILL THE BURN POT

WITH THE RIGHT AMOUNT OF PELLETS TO START THE FLAME REGULARLY.

IF THE PROBLEM OCCURS ONLY AFTER A FEW MONTHS OF OPERATION, MAKE SURE THAT THE ROUTINE CLEANING

OPERATIONS INDICATED ON THE STOVE BOOKLET HAVE BEEN CARRIED OUT PROPERLY

NEVER USE FLAMMABLE LIQUIDS FOR IGNITION!

WHILE FILLING, DO NOT BRING THE PELLET BAG IN CONTACT WITH THE BOILING STOVE!

IN CASE OF CONTINUOUS FAILED IGNITIONS, CONTACT AN AUTHORISED TECHNICIAN.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Terry plus Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Terry plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info