Bedienungsanleitung FAAC 455 (Seite 20 von 28) (Englisch)

119529

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Page 20

January, 2004

412 Operator And

455 D Control Panel Installation Manual

PROGRAMMING

To program the automated system, the

“Programming Mode” must be accessed.

Programming is split into two parts: BASIC and

ADVANCED.

BASIC PROGRAMMING

To access BASIC PROGRAMMING, press the “F” key.

• If you press it (and hold it down), the display

shows the name of the first function.

• If you release the key, the display shows the

value of the function that can be modified with

keys + and — .

• If you press and hold down the “F” key again

(and hold it down), the display shows the name

of the next function, etc.

• When you reach the last function, press “F” to

exit the program, and the display resumes

showing the status of the inputs.

The table on the right shows the sequence of

functions accessible in BASIC PROGRAMMING.

ADVANCED PROGRAMMING

To access ADVANCED PROGRAMMING, press the “F”

key and, as you hold it down, press the “+” key:

• If you release the “+”, the display indicates the

name of the first function.

• If you release the “F” key, too, the display

shows the value of the function that can be

modified with keys “+” and “—”.

• If you press the “F” key (and hold it down), the

display shows the name of the next function,

and if you release it, the value that can be

modified with keys “+” and “—”.

• When you reach the last function, press the “F”

key to exit the program, and the display

resumes showing the status of the inputs.

The table on page 21 shows the sequence of

functions accessible in ADVANCED PROGRAMMING.

Display Function Default

PERATING LOGICS

A = Automatic (Timer to Close)

E = Semi Automatic

S = Security

EP = (Semi-Automatic) Step by Step

B = Manned, Pulsed

C = Manned, constant

AUSE TIME

This is the time between open and

closing and is adjustable from 0 to

4 min. This is only true in “A”

Mode. (see pause time description)

ORCE/TORQUE MOTOR 1

This adjusts the force / torque that

motor 1 is applying to the gate

leaf. Setting is 0 to 50.*

ORCE/TORQUE MOTOR 2

This adjusts the force / torque that

motor 2 is applying to the gate

leaf. Setting is 0 to 50.*

LOSING LEAF DELAY

Delays the closing of operator

wired into motor one outputs. Ad-

justable from 0 to 4 minutes

(Same as pause time)

OTOR RUN TIME

This enables where you choose

from “simple” learning or

“complete” learning of the motor

run time. See page 10 & 11 for

complete details.

Simple Learning

~ 1 s.

Complete Learning

> 3 s.

XIT PROGRAMMING

Exit from programming and return

to display of inputs status.

BASIC PROGRAMMING

* With Hydraulic operators the Force/Torque must be set to

the maximum setting of 50.

PROGRAM BUTTONS

+ -

LEFT MIDDLE RIGHT

THE 455 D CONTROL PANEL INSTALLATION INSTRUCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

FAAC 455 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von FAAC 455

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info