Bedienungsanleitung FAAC 455 (Seite 22 von 28) (Englisch)

119529

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

• When gate operator (1) reaches the position

that you want it to slow down, an open

command must be given to start the slow

down phase.

• When gate operator (1) reaches the positive

stop and the desired motor run time has

been reached, an open command must be

given to shut the motor off. At this point

gate operator (2) will automatically start to

open.

• When gate operator (2) reaches the position

that you want it to slow down, an open

command must be given to start the slow

down phase.

• When gate operator (2) reaches the positive

stop and the desired motor run time has

been reached, an open command must be

given to shut the motor off. At this point

gate operator (2) will automatically start to

close.

• When gate operator (2) reaches the position

that you want it to slow down, an open

command must be given to start the slow

down phase.

• When gate operator (2) reaches the positive

stop and the desired motor run time has

been reached, an open command must be

given to shut the motor off. At this point

gate operator (1) will automatically start to

close.

• When gate operator (1) reaches the position

that you want it to slow down, an open

command must be given to start the slow

down phase.

• When gate operator (1) reaches the positive

stop and the desired motor run time has

been reached, an open command must be

given to shut the motor off.

The display stops flashing and the gate is ready for

normal operation.

LEARNING TIMES WITH GATECODER

Learning with the Gatecoder can be done in two

different ways:

SIMPLE LEARNING

Close the gates, enter “Basic Programming”, select the

TIME LEARNING function and press the + push-button

for 1 second: the display begins flashing and the

leaves begin the opening movement.

The movement stops automatically when the opening

positive stop is reached and the display stops

flashing.

LEARNING OF OPERATING TIMES

WARNING:

During the learning procedure, the

safety devices are disabled

! Therefore, any and

all traffic must be avoided in the path of the gate

leaf(s).

NOTE: Programming must start with the gate(s)

in the closed position.

Opening/closing time is established by the learning

procedure which varies slightly according to whether

you are or are not using Gatecoders.

LEARNING OF NORMAL TIMES

Normal learning (i.e. without Gatecoders) can be done

in two different ways:

SIMPLE LEARNING (WITHOUT SLOW DOWN)

Close the gates, enter “B

ASIC PROGRAMMING”, select the

TIME LEARNING function and press the + push-button

for 1 second the display begins flashing and the

leaves begin the opening movement.

Wait for the leaves to reach the opening positive stop

and then supply an OPEN A command after the

desired motor run time has been reached (by push-

button or radio control) to stop the movement: the

leaves stop and the display stops flashing. One more

command given will close the gate.

The procedure has ended and the gate is ready to

operate.

COMPLETE LEARNING (WITH SLOW DOWN)

NOTES:

•

If you do not wish to slow the gate operator

(s) down, wait for the gate to reach its

positive stop and supply two (2) consecutive

open commands (within 1 second).

• If only one gate operator (1) is used, you

must go through the entire programming

procedure, as if you were programming for

two gate operators (2). When the operator

has finished opening, supply 5 open

commands until the gate operator begins to

close, and then resume normal operations.

Close the gates, enter “B

ASIC PROGRAMMING”, select the

TIME LEARNING function and press the + push-button

for more than 3 seconds: the display begins flashing

and leaf 1 begins opening. The following functions

can be commanded by the OPEN A (by push-button

wired to terminals 9 and 14, or radio control):

Page 22

January, 2004

412 Operator And

455 D Control Panel Installation Manual

THE 455 D CONTROL PANEL INSTALLATION INSTRUCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

FAAC 455 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von FAAC 455

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info