Bedienungsanleitung FAAC S450H (Seite 2 von 11) (Englisch)

560682

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

ENGLISH

1) ATTENTION! To ensure personal safety, carefully read following instructions.

Improper installation or misuse of the product can cause serious personal

injuries.

2) Carefully read the instructions before installing the product.

3) Packaging material (plastic, polystyrene, etc.) is a potential hazard and

must be kept out of reach of children.

4) Keep these instructions for future reference.

5) This product was designed and manufactured exclusively for the purpose

indicated in this documentation. Any other use, not expressly indicated

here, could compromise the good condition/operation of the product

and/or be a source of danger.

6) FAAC declines any responsibility for improper use or use other than that

for which the automated system was intended.

7) Do not install the equipment in an explosive atmosphere: the presence

of inflammable gas or fumes is a serious danger to safety.

8) Mechanical constructive elements must comply with the requirements

of the EN 12604 and EN 12605 standards.

In addition to their national legal regulations, countries outside the EC

must follow the above mentioned standards in order to guarantee an

adequate level of safety.

9) FAAC cannot be held responsible for failure to observe technical standards

in the construction of the closing elements to be motorised nor for any

deformation which may occur during use.

10) The installation must be carried out in conformity with the EN 12453 and

EN 12445 standards.

In addition to their national legal regulations, countries outside the EC

must follow the above mentioned standards in order to guarantee an

adequate level of safety.

11) Disconnect the power supply before any operation on the system.

12) The power mains of the automated system must be fitted with a multi-pole

power switch with a switch-contact gap of at least 3 mm. The use of a 6-

A thermomagnetic switch with multi-pole switching is recommended.

13) Make sure that a differential switch with trip threshold of 0.03 A is fitted

upstream of the system.

14) Make sure that the earthing system is at the state of art and connect

to the metallic parts of the closing system.

15) The automated system is equipped with an intrinsic anti-crushing safety

device of the torque control type. Its tripping threshold must be verified

according to the requirements specified in the Standards listed in 10.

16) The safety devices (EN 12978) protect from the hazards caused by

mechanical movements, such as crushing, entrapment and shearing

hazards.

17) Each installation should be fitted with at least one flashing light (e.g.

FAACLIGHT) and a warning sign suitably secured to the frame structure,

in addition to the devices described in 16 above.

18) FAAC declines any responsibility regarding safety and efficient operation

of the automated system if parts other than FAAC original parts are

used.

19) Use only FAAC original parts for maintenance.

20) Do not in any way modify the automated system components.

21) The installer shall provide all information concerning the manual

operation of the system in the event of an emergency and shall

hand over to the end-user the warning instructions supplied with the

product.

22) Keep children, adults or objects away from the product while it is

operating.

23) Keep remote controls or other pulse generators out of reach of children, to

prevent the automated system from being activated unintentionally.

24) Transit is permitted only when the automated system is non in

operation.

25) The automated system cannot be repaired/adjusted by the end-user;

these operations can only be carried out by qualified personnel.

26) Maintenance: the functional check of the system must be carried out

at least every six months; pay special attention to the good working

condition of the release and safety devices (including, where foreseen,

the thrust force of the operator).

27) Feed the automation system only when explicitly stated.

28) Anything not expressly specified in these instructions is not permitted.

IMPORTANT INSTRUCTIONS

FOR THE INSTALLER GENERAL SAFETY

CE DECLARATION OF CONFORMITY FOR MACHINES

(DIRECTIVE 2006/42/EC)

Manufacturer: FAAC S.p.A.

Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY

Declares that: Operator mod. S450H

is built to be integrated into a machine or to be assembled with other machinery to create a machine under the provisions

of Directive 2006/42/EC

complies with the essential safety requirements of the following EEC directives:

2006/95/EC Low Voltage Directive

2004/108/EC Electromagnetic Compatibility Directive

It further declares that it is not allowed to put the device in operation until the machine it has to be integrated into or of which it is going

to become an integral part has been identified and its conformity has been declared under the provisions of the Directive 2006/42/EEC

and subsequent amendments.

Bologna, 01.02.11

The Managing Director

A. Marcellan

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

FAAC S450H Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von FAAC S450H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info