Bedienungsanleitung FAAC S450H (Seite 3 von 11) (Englisch)

560682

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

1113

750

311

119

S450H

ENGLISH

1 DESCRIPTION AND TECHNICAL SPECIFICATIONS

1.1 DIMENSIONS

a Front fitting

b Cover

c Emergency release with key

d Plastic cover for rear bracket

e Rear bracket

f Encoder

g Spacer for opening mechanical stop

TECHNICAL

SPECIFICATIONS

CBAC

OPERATOR

Power supply (V dc) 24 - 36

Power consumption (W) 60 (nominal) - 288 (maximum)

Protection class IP 55

Oil type FAAC HP OIL

Operating temperature -20°C +50°C

R.O.T. (24V) Continuous at 55°C

Hydraulic lock Installed Not installed

Traction/thrust force

max (N)

5000 (E124) - 3600 (E024S)

Max. opening angle See table 1

Max. leaf length (m) 2 3

Rod linear speed (Cm/s) 2,5 (E124) - 2,0 (E024S)

Effective rod stroke (mm) 311

Operator weight (kg) 7.1 6.9

2 PRESETTINGS

b RX Photocells (receiver)

(TRADITIONAL: 4 x 0.5 mm²; 2easy bus: 2 x 0.5 mm²)

TX Photocells (transmitter) (2 x 0.5 mm²)

c Electronic control unit

(power supply 3 x 1.5 mm²)

d Key-operated push-button (e.g. T11) (3 x 0.5 mm²)

e Flashing lamp 24 V dc (2 x 1 mm²)

f Opening mechanical stops*

g Electric lock and closing mechanical stop

(2 x 1.5 mm)

3 INSTALLATION OF THE AUTOMATED SYSTEM

Following conditions have to be met to ensure safety and the

efficient operation of the automated system:

• The gate structure must be suitable for automation. Verify in

particular that it is sufficiently strong and stiff and that dimensions

and weight correspond to those stated in the technical

specifications.

• Verify the smooth and uniform movement of leaves, without

irregular friction during the whole travel.

• Verify the good condition of hinges.

• Verify the presence of mechanical limit switches.

• Remove any locks and bolts.

Carry out any metalwork operations before installing the

automated system.

Fig. 1

Fig. 2

The FAAC S450H automated system for swing-leaf gates consists

of an electrical pump and an hydraulic piston transmitting the

leaf movement, assembled in a single block.

The model with hydraulic lock can automate leaves up to 2 m.

It does not require the installation of electric locks and guaran

tees that the leaf is mechanically locked when the motor is not

in operation. The model without hydraulic lock always needs

one or more electric locks to guarantee the leaf mechanical

lock. The S450H automated systems have been designed

and built to automate swing-leaf gates. Avoid any other use

whatever.

Without encoder the automated system does not operate

correctly.

Fig. 3

Dimensions in millimeters

* CONSIDERING 40 bar (E124) 30 bar (E024) STATIC PRESSURE

ON PISTONE

** CONSIDERING A RANGE OF PUMP 1.5 lpm (E124) AND 1.2

lpm (E024S)

DISTANCE (m)

20 m 35 m 50 m

ø MOTOR CABLE

2x2.5 mm² 2x4 mm² 2x6 mm²

ø 2 easy bus

ENCODER CABLE

2x0.5 mm² 2x0.5 mm² 2x0.5 mm²

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

FAAC S450H Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von FAAC S450H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info