Bedienungsanleitung Faber Stockbridge 2.0 (Seite 29 von 40) (Deutsch, Englisch, Holländisch, Französisch, Norwegisch)

706553

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Operating the Fire

This section describes how to activate your ﬁ re using either the manual controls or remote control.

MANUAL CONTROLS

The manual controls are located beneath the hinged ﬂ ap. Open the doors to access the controls. (See Fig.10 for

Manual Control lay out)

Switch ‘A’:- Controls the electricity supply to the Fire.

Note: This switch must be in the ‘ON’ ( I ) position for the Fire to operate either with or without heat.

Switch ‘B’:- Press

once to turn on the ﬂ ame effect. This will be indicated by an audible beep. Although the main

lights operate immediately it will take a further 30 seconds before the ﬂ ame effect starts.

Press again to give ﬂ ame effect and half heat. This will be indicated by two beeps.

Press again to give ﬂ ame effect and full heat. This will be indicated by three beeps.

Press again to return to ﬂ ame effect only. This will be indicated by one beep.

Press to put ﬁ re in to standby mode. This will be indicated by one beep.

Control Knob ‘C’:- Controls the Thermostat setting.

Turning the control knob to the left will decrease the temperature setting, turning the control knob

to the right will increase the temperature setting.

Control Knob ‘D’:- Controls the intensity of the ﬂ ame effect.

Turning the control knob to the left increases the ﬂ ame effect, turning the control knob to the right will

decrease the ﬂ ame effect.

SETTING THE THERMOSTAT

Ensure the ﬁ re is plugged in and switch it on to the full heat setting. Turn the Control Knob ‘C’ fully to the right (max

temperature setting) to warm the room rapidly. When the room temperature has reached the desired level, turn

the thermostat knob back slowly until you hear the thermostat just click off. The heater will then maintain the room

temperature at the chosen level.

Note: Should your heater fail to come on when the thermostat is at a low setting, this may be due to the room

temperature being higher then the thermostat setting

THERMAL SAFETY CUT-OUT

A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating. This can happen

if the heat outlet was restricted in any way or if the chimney ﬂ ue has not been blocked off effectively.. If the cut-out

operates, unplug the heater from the socket outlet and allow approximately 10 minutes before reconnecting. Before

switching the heater back on remove any obstruction that may be restricting the heat outlet, then continue normal

operation.

Caution: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be

supplied through an external switching device, such as a timer, or connected to a switch that is regularly switched

on and off by the utility. Depending on room temperature and humidity upon initial start up there may be some

condensation on the inside of the stove. This can be overcome by turning the ﬂ ame control knob down and leaving the

door of the stove slightly ajar, until the glass warms up.

GETTING THE DESIRED FLAME EFFECT

1. The ﬂ ame control knob ‘D’ (Fig.10) may be turned up or down to give a more realistic effect.

2. Generally the ﬂ ames appear more realistic when the ﬂ ame control is turned down.

3. Give the ﬂ ame generator time to react to changes you may make.

4. The ﬁ re will use less water if the ﬂ ame effect is set to a lower level.

5. Do not tilt or move the ﬁ re while there is water in the tank or sump.

6. Make sure that the ﬁ re is on a level ﬂ oor.

REMOTE CONTROL OPERATION

On the control panel, Switch A (see Fig.10) must be in the ‘ON’ ( I ) position in order for the remote control to operate.

There are 3 buttons on the remote control. (See Fig.12) To operate correctly the remote must be pointed towards the

front of the grate. (See Fig 17). The remote control functions are as follows:

Press once to turn on Flame effect only.

This will be indicated by one beep.

Press once to turn on Half Heat and Flame Effect.

This will be indicated by two beeps.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Stockbridge 2.0 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info