Bedienungsanleitung Falcon 211 EEO Ceramic (Seite 25 von 32) (Englisch)

500338

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity supply before servicing. Check appliance is safe when you have finished.

Page 25

Note

Ensure that the floor covering below the range is firmly fixed or

removed to prevent disturbance whilst positioning the appli-

ance.

Figure 2

1.2.2 Levelling

The unit must be levelled following placement. The height at

the back is adjusted by using the hex end of the spanner on

the rear rollers. The front is levelled by initially turning the ad-

justing screw of the near roller clockwise until the desired

height is achieved. Following this, position the levelling feet by

screwing them down. When the unit is level, turn the front

roller adjuster anti-clockwise until the weight is transferred

from the roller to the feet.

1.2.3 APPLIANCE LOCATION

The unit may be installed in a kitchen/kitchen diner but not in a

room that contains a bath or shower.

1.2.4 Position of Appliance

The space required above the hotplate is indicated in Figure

A width of 1115mm is required up to hotplate level to accom-

modate the additional width required when the doors are

opened fully.

A minimum overhead distance of 800mm is required above

the hob.

Curtains must not be fitted immediately behind the appliance.

Any extraction hood should be installed in accordance with

the manufacturer’s instructions.

1.3 ELECTRICAL SUPPLY

1.3.1 ELECTRICAL CONNECTION

This appliance must be installed by a qualified elec-

trician to comply with the relevant Institute of

Electrical Engineers (I.E.E.) regulations and also lo-

cal electricity supply company requirements.

WARNING - THIS APPLIANCE MUST BE EARTHED!

Note: The unit must be connected to the correct electrical sup-

ply as stated on the data label. A suitable control unit which

incorporates a double pole switch with contact separation of at

least 3mm in all poles must be fitted. This type of unit should

NEVER be connected to a regular power socket.

With diversity taken into consideration, we recommend the

use of a 40 - 45 amp cooker point.

Access to mains terminal is gained by removing electrical ter-

minal cover box on back panel. Connect mains cable to

terminals as indicated below.

Fig. 4

The unit is Type X with regard to protection against the over-

heating of surrounding surfaces.

Current Operated Earth Leakage Breakers

In the event of an installation being protected by a 30mA sen-

sitivity residual current device (RCD), the combined use of the

unit and other domestic appliances may occasionally cause

nuisance tripping. In such instances, the cooker circuit may re-

quire to be protected by fitting a 100mA device. Such work

should be carried out by a qualified electrician.

1.4 ELECTRICAL RATINGS

1.4.1 Hob Element Ratings (230V - 50hz)

Hob Element Rating

Front Left 1.1kW

Rear Left 1.4kW

Rear Right 1.1kW

Front Right 1.1kW

Centre 2.7kW

1.4.2 ADDITIONAL ELECTRICAL RATINGS (230V

- 50HZ)

LH Oven - 2.0kW Browning Element 1.05kW

RH Oven - 2.3kW Grill Element 2.1kW

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falcon 211 EEO Ceramic Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info