Bedienungsanleitung Falcon 211 EEO Ceramic (Seite 26 von 32) (Englisch)

500338

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity supply before servicing. Check appliance is safe when you have finished.

Page 26

SECTION 2 - ASSEMBLY and

COMMISSIONING

2.1 ASSEMBLY

After unpacking unit, check following parts -

Part No. Off

Oven Shelves 4

Grill Pan and Grid I

Ceramic Hob Scraper 1

Roasting Tin with Trivet 2

Cake Rack 2

Handy Rack 1

User’s Manual 1

2.2 CONNECTION TO THE ELECTRICITY SUPPLY

Refer to Section 1.3 of this manual.

2.4 PRE-COMMISSIONING CHECK

Check hob elements in turn. Turn control knob to full on

position and leave hob for a few seconds before checking

that heat is radiating from the element.

When check is complete, turn control off and repeat this

procedure for the remaining elements. Check also that

the residual heat indicator remains lit until the corre-

sponding element cools.

SECTION 3 - SERVICING

3.1 SERVICING

Disconnect from electricity supply before commencing

servicing, particularly before removing any of the follow-

ing:- control panel, side panels, ceramic hob or any

electrical components or covers.

Before restoring power, make connection checks as de-

tailed in Section 1.3. Note - References to LH and RH

oven apply as viewed from the front.

3.2 TO REMOVE CONTROL PANEL

Disconnect appliance from electricity supply.

a) Remove control knobs from all taps.

b) Open grill and RH oven doors. Remove 3 fixings on top

front and 3 fixings on control panel underside.

c) Pull control panel forward. Remove connections from

rear of three neons. Disconnect earth lead and lift panel

clear of unit.

d) Replace all parts in reverse order.

e) When replacing any electrical connections refer to the

wiring diagram on Pages 16 and 17.

3.3 TO REMOVE CERAMIC HOB

Disconnect appliance from electricity supply. Pull unit forward

to gain access.

The ceramic hob material is much more sensitive to

scratches on the underside than the top.

Take care not to touch or scratch the underside of

the ceramic as this will weaken the material and

cause the top to shatter.

a) Remove control panel as detailed in Section 3.2.

b) Remove fixing screws on hob underside (2 - front, 4 -

rear).

c) Lift rear and slide ceramic hob forward.

d) Lift ceramic hob clear of appliance taking care not to

damage elements.

e) Replace in reverse order.

3.4 TO REMOVE AN OUTER SIDE PANEL

Disconnect the appliance from the electricity supply.

a) Remove control panel as detailed in Section 3.2.

b) Remove retaining screw on upper front edge and two

fixings on rear of the side panel. Undo lower retaining

screw situated below the edge at panel front corner.

c) Remove panel by pulling it away from unit. If this is diffi-

cult, it may be necessary to slacken the two closest hob

fixing screws

d) Replace parts in reverse order.

3.5 TO REMOVE A RESIDUAL HEAT

INDICATOR

Disconnect appliance from electricity supply.

a) Remove control panel as detailed in Section 3.2.

b) Remove ceramic hob as detailed in Section 3.3.

c) Disconnect the indicator leads.

d) Remove indicator from bracket.

c) Replace all parts in reverse order.

Ensure replacement indicator functions correctly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falcon 211 EEO Ceramic Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info