Bedienungsanleitung Falcon 900 deluxe inox (Seite 23 von 32) (Englisch)

326872

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Conversion to LP

If the appliance is to be converted to LP gas do the

conversion at this point. See the conversion section

of these instructions.

Levelling

You are recommended to use a spirit level on a shelf

in one of the ovens to check for level.

Place the cooker in its intended position taking care

not to twist it within the gap between the kitchen units

as damage may occur to the cooker or the units.

The front feet and rear rollers can be adjusted to

level the cooker. To adjust the height of the rear of

the cooker use the levelling tool supplied to turn the

adjusting nuts at the front bottom corners of the

cooker. To set the front feet turn the bases to raise

or lower.

Gas Connection

Fitting a stability bracket

A stability bracket or chain (not supplied by with

the cooker) should be fitted when the cooker is

connected to a flexible gas supply. Any restraining

device should be secured to the fabric of the building

and should be able to be released so that the cooker

can be pulled out for cleaning and maintenance.

When fitting a stability bracket read these

instructions together with the leaflet supplied with the

bracket.

a) Position and level the appliance.

b) Draw a pencil line 70mm from the front edge of

the levelling feet.

c) Mark off 350mm from the RH side of the unit to

indicate the centre line for the bracket.

d) Remove the range.

e) Mark off 500mm to locate the front edge of the

lower bracket. Fix bracket to floor.

f) Measure the height from floor level to the top

edge of the rear channel. Add 3mm to this

dimension and assemble the stability bracket to

this height (i.e. from floor level to underside of top

member)

Gas Connection

The Gas supply needs to terminate with a down

facing bayonet. The rear cover boxes limit the

position of the supply point.

view from the rear

A position for gas supply connector

B appliance gas inlet

Because the height of the cooker can be adjusted

and each connection is different it is difficult to give

precise dimensions. Ideally the house supply

bayonet should be in the shaded area shown in the

diagram. Although a 900mm hose can be used, a

1250mm hose will allow slightly more flexibility in the

positioning of the bayonet and make moving the

cooker easier. The hose should be fitted so that both

inlet and outlet connections are vertical so that the

hose hangs downwards.

The hose should be fitted so that both inlet and outlet

connections are vertical so that the hose hangs

downwards in a ‘U’ shape.

For Natural Gas the flexible hose must be in

accordance with B.S.669.

For LP Gas it should be capable of 50mbar

pressure, 70C temperature rise and carry a red

stripe, band or label.

If in doubt contact, your supplier.

Screw connect the threaded end of the hose into the

gas inlet in the underside of the connector block on

the back of the cooker.

After completing the gas connection, check the

cooker is gas sound with a pressure test. When

checking for gas leaks do not use washing up liquid -

this can corrode. Use a product specifically

manufactured for leak detection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falcon 900 deluxe inox Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Falcon 900 deluxe inox

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info