Bedienungsanleitung Falcon De Luxe 1092 Continental (Seite 25 von 56) (Deutsch, Englisch)

500340

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

SERVICING  WARNING

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

Servicing

1 SERVICING

When servicing or replacing gas carrying components,

disconnect from the gas supply before commencing operation.

Check the appliance is gas sound after completion of service.

When checking for gas leaks do not use washing up liquid - this

can corrode. Use a product speciﬁ cally manufactured for leak

detection.

Do not use re-conditioned or unauthorised gas controls.

Disconnect from the electricity supply before commencing

servicing, particularly before removing any of the following:

- control panel, side panels, hotplate tray or any electrical

components or covers.

Before electrical re-connection, check that the appliance is

electrically safe.

Note - References to LH and RH oven apply as viewed from the

front.

BEFORE SERVICING ANY GAS CARRYING COMPONENTS. TURN

OFF THE GAS SUPPLY.

2 To Remove the Hotplate

Disconnect the appliance from the electricity supply.

Pull the unit forward to gain access.

a) Remove the pan supports/hotplate accessories and

burner caps.

b) Remove the brass venturi in the centre of each hotplate

burner bezel.

c) Remove the bezel from the hotplate and disconnect the

spark ignition lead from the spark electrode.

d) Lift the hotplate clear of the appliance.

e) Replace in reverse order.

3 To Remove the Control Panel

Disconnect the appliance from the electricity supply.

a) Remove the pan supports/hotplate accessories and

burner caps.

b) Slacken the brass venturi at the centre of each burner.

c) Remove the control knobs from all taps.

d) Open both oven doors. Remove 3 ﬁ xings on the top front

and 3 ﬁ xings on the control panel underside.

e) Pull the control panel forward. Remove the connections

from the rear of the three neons. Disconnect the earth

lead and lift the panel clear of the unit.

f) Replace all parts in reverse order.

g) When replacing any electrical connections refer to the

wiring diagram.

4 To Remove an Outer Side Panel

Disconnect the appliance from the electricity supply.

a) Remove the control panel as detailed in Section 3

b) Remove the retaining screw on the upper front edge

and the two ﬁ xings on the rear or the side panel. Undo

the lower retaining screw situated below the edge at the

panel front corner.

c) Remove the panel by pulling it away from the unit.

Should diﬃ culty be encountered, it may be necessary to

slacken the two closest burners and both brass venturi as

detailed in Section 2.

d) Replace parts in reverse order. Ensure that both venturis

are fully tightened.

5 To Remove an Oven Neon

Disconnect the appliance from the electricity supply.

a) Remove the control panel as detailed in Section 3

b) Remove the relevant neon connection and undo the nut

which secures the neon to the control panel.

c) Replace parts in reverse order. Ensure the replacement

neon functions correctly.

6 To Remove a Thermostat

Disconnect the appliance from the electricity supply.

Remove the hotplate - see 2. Remove the control panel - see 3.

Open the appropriate oven door and remove the oven shelves.

Pull the appliance forward to gain access to the rear cover box.

Undo the cover screws and lift clear.

Right Hand oven

Remove the two ﬁ xings that secure the thermostat phial cover.

Unclip the thermostat phial from the clips in the oven back

panel.

Left Hand oven

Remove the two screws holding the thermostat phial to the

oven fan cover at the rear of the oven. Pull the unit forward

to access the rear of the cooker. Remove the cover boxes

by removing the ﬁ xing screws and lifting clear. Feed the

thermostat capillary clear of the oven.

Disconnect the wires from the thermostat and undo the two

ﬁ xings that secure the control to the mounting plate.

Fit the replacement and re-assemble in reverse order. Ensure

that the phial is clipped to the oven rear, positioned centrally

between the clips. Check that the thermostat functions

correctly.

7 To Remove an Oven Cut-Oﬀ Thermostat

Disconnect the appliance from the electricity supply.

a) Pull the unit forward to gain access to the cover box.

Undo the cover screws and lift clear.

b) The control is located on the earth plate beside the oven

element connections.

c) Disconnect the thermostat wiring. Undo the ﬁ xings that

secure the thermostat to the earth plate and remove.

d) Fit replacement control and re-assemble parts in reverse

order.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falcon De Luxe 1092 Continental Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Falcon De Luxe 1092 Continental

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info