Bedienungsanleitung Falcon De Luxe 1092 (Seite 42 von 76) (Deutsch, Englisch, Französisch)

500337

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

English

Place the cooker in its intended position taking

care not to twist it within the gap between the

kitchen units as damage may occur to the

cooker or the units.

The rollers can be adjusted to level the cooker.

To adjust the height of the rear of the cooker

use the levelling tool supplied to turn the

adjusting nuts at the front bottom corners of the

cooker.

Adjust the height of the front roller to level the

cooker. Turn clockwise to raise the cooker and

anticlockwise to lower.

When you are satisfied with the height and level

raise the front of the cooker by one turn of the

front roller adjuster. Screw down the front feet to

meet the floor. Screw the front roller adjuster

anticlockwise to raise the front roller so that the

front of the cooker is supported on the feet, not

the front roller, to prevent accidental movement

of the cooker.

Leave the levelling tool in the storage drawer, so

that the customer can use it if they wish to move

the cooker.

Replace the drawer by locating on side runners

and push in.

Gas Connection

Restraining device

A restraining device should be fitted when the

cooker is connected to a flexible gas supply.

Any restraining device should be secured to the

fabric of the building and should be able to be

released so that the cooker can be pulled out for

cleaning and maintenance.

Flexible Gas Hose

A gas shut off valve must be fitted between the

gas supply and the connection hose. The

flexible hose (not supplied with the cooker) must

be in accordance with the relevant standards. If

in doubt contact, your supplier.

The rear cover boxes limit the position of the

supply point. The house gas supply needs to

terminate with a down facing connection.

view from the rear

A position for gas supply connector

B appliance gas inlet

The appliance connection is located just below

hotplate level at the rear of the cooker. (‘B’ in

the figure)

The hose should be fitted so that both inlet and

outlet connections are vertical so that the hose

hangs downwards in a ‘U’ shape.

Because the height of the cooker can be

adjusted and each connection is different it is

difficult to give precise dimensions. Ideally the

house supply connection should be in the

shaded area shown in the figure showing the

back of the cooker. (‘A’ in the figure)

After completing the gas connection, check the

cooker is gas sound with a pressure test. When

checking for gas leaks do not use washing up

liquid - this can corrode. Use a product

specifically manufactured for leak detection.

Pressure testing

The gas pressure can be measured at the pressure

test point on the gas connection block. Turn and light

one of the hotplate burners.

For Natural Gas the pressure should be 20mbar.

Reassemble burner top, making sure it is

reassembled in the correct way on the burner body.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Falcon De Luxe 1092 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Falcon De Luxe 1092

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info