44
English
b) Remove the brass venturi in the centre of each
hotplate burner bezel.
c) Remove the bezel from the hotplate and
disconnect the spark ignition lead from the spark
electrode.
d) Lift the hotplate at the front and disconnect the
hotplate earth lead. Lift the hotplate clear of the
appliance.
e) Replace in reverse order.
3 To Remove the Control Panel
Disconnect the appliance from the electricity supply.
a) Remove the pan supports/hotplate accessories
and burner caps.
b) Slacken the brass venturi at the centre of each
burner.
c) Remove the control knobs from all taps.
d) Open the grill and RH oven doors. Remove 3
fixings on the top front and 3 fixings on the control
panel underside.
e) Pull the control panel forward. Remove the
connections from the rear of the three neons.
Disconnect the earth lead and lift the panel clear of
the unit.
f) Replace all parts in reverse order.
g) When replacing any electrical connections refer to
the wiring diagram.
4 To Remove an Outer Side Panel
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 3
b) Remove the retaining screw on the upper front
edge and the two fixings on the rear or the side
panel. Undo the lower retaining screw situated
below the edge at the panel front corner.
c) Remove the panel by pulling it away from the unit.
Should difficulty be encountered, it may be
necessary to slacken the two closest burners and
both brass venturi as detailed in Section 2.
d) Replace parts in reverse order. Ensure that both
venturis are fully tightened.
5 To Remove an Oven or Grill Neon
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 3
b) Remove the relevant neon connection and undo
the nut which secures the neon to the control
panel.
c) Replace parts in reverse order. Ensure the
replacement neon functions correctly.
6 To Remove a Thermostat
Disconnect the appliance from the electricity supply.
a) Remove the hotplate as detailed in Section 2.
b) Remove the control panel as detailed in Section 3
c) Open the appropriate oven door and remove the
oven shelves.
RH oven
Remove the two fixings that secure the thermostat
phial cover. Unclip the thermostat phial from the
clips in the oven back panel.
LH oven
Remove the two screws holding the thermostat
phial to the oven fan cover at the rear of the oven.
Pull the unit forward to access the rear of the
cooker. Remove the both cover boxes by removing
the fixing screws and lifting clear. Feed the
thermostat capillary clear of the oven.
d) Disconnect the wires from the thermostat and undo
the two fixings which secure the control to the
mounting plate.
e) Fit the replacement and re-assemble in reverse
order. Ensure that the phial is clipped to the oven
rear, positioned centrally between the clips. Check
that the thermostat functions correctly.
7 To Replace a Grill Controller
Disconnect the appliance from the electricity supply.
a) Remove the hotplate as detailed in Section 2.
b) Remove the control panel as detailed in Section 3.
c) Disconnect the controller wiring. Undo the fixings
that secure the device to the mounting plate.
d) Fit the replacement and re-assemble parts in
reverse order. Check that the replacement
functions correctly.
8 To Remove an Oven Cut-Off Thermostat
Disconnect the appliance from the electricity supply.
a) Pull the unit forward to gain access to the cover
box. Undo the cover screws and lift clear.
b) The control is located on the earth plate beside the
oven element connections.
c) Disconnect the thermostat wiring. Undo the fixings
that secure the thermostat to the earth plate and
remove.
d) Fit replacement control and re-assemble parts in
reverse order.
9 To Remove a Hotplate Tap
a) Remove the hotplate as detailed in Section 2.
b) Remove the control panel as detailed in Section 3.
c) Unplug the FSD lead from the rear of the tap. Undo
compression fitting at the rear of the tap. Remove
the fixings that secure the tap to the gas rail.
Disconnect the ignition switch wiring.
d) Remove the tap. Remove and discard the gasket
seal. Fit new gasket seal to replacement tap.
e) Re-assemble in reverse order. Check the
appliance is gas sound. Check hotplate ignition.
10 To Change an Ignition Switch
Change the gas tap as detailed in Section 9.
11 To Remove a Hotplate Burner Injector
a) Remove the hotplate as detailed in Section 2.
b) Remove the injector directly from the burner body.
c) Fit the appropriate injector.
d) Re-assemble in reverse order. Check the
appliance is gas sound.
