659394

Falcon Toledo 90 Seite 33

33
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have nished.
29
2 Hotplate
BEFORE SERVICING ANY GAS CARRYING
COMPONENTS, TURN OFF THE GAS SUPPLY.
2.1 To Remove the Hotplate
Pull the cooker forward to gain access to the rear.
Left-hand tray
From the rear remove the screws securing the ue grill
to the hotplate tray. Remove pan supports, burner
heads and caps. Remove the 4 screws and washers
holding the hotplate tray to the frame. Raise the front of
the hotplate then withdraw.
Right-hand tray
From the rear remove the screws securing the ue grill
to the hotplate tray. If the left-hand hotplate has not
been removed, slacken the screws holding the left-hand
tray. Remove the pan support, burner head, caps and
trim rings. Remove the screws holding the wok burner
to the hotplate. Remove the 2 screws and washers
holding the right-hand tray to the frame.
Press the wok burner down slightly and, taking care
not to damage the wok burner electrode, slide the tray
about 30 mm to right to clear the locating brackets on
the right-hand side and withdraw the hotplate.
Reassemble in reverse order. When replacing the right-
hand hotplate take care not to damage the ignition
electrode of the wok burner.
It is important that the rear xing screws are retted as
they from part of the cooker earthing.
It is important that the rear xing screws are retted as
they from part of the cooker earthing.
On some models there is a separate plate (Fig.9-2). On
others it is a tag on the cooker backsheet (Fig.9-3).
It is important that the tag is on the outside and that
both xing screws are tted.
Check for correct burner operation.
2.2 To Replace the Hotplate Control Taps
DISCONNECT FROM THE ELECTRICITY SUPPLY.
BEFORE SERVICING ANY GAS CARRYING
COMPONENTS, TURN OFF THE GAS SUPPLY.
Remove the control panel and hotplate (see 1.1 & 2.1).
Unplug the FSD lead from the rear of the tap. Undo the
compression tting at the rear of the tap and remove
the xings that secure the tap to the gas rail. Disconnect
the ignition switch wiring.
Remove the tap. Remove and discard the gasket seal. Fit
the new gasket seal to the replacement tap. Reassemble
in reverse order. Check that the appliance is gas sound.
Verify the hotplate ignition.
2.3 To Change a Hotplate Burner Injector
Remove the burner cap and head. Remove the old
injector.
Fit the new injector. Reassemble in reverse order. Check
the appliance is gas sound.
2.4 To Replace a Hotplate Burner Electrode
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Lift o pan supports and remove the burner cap.
Remove the screw holding the electrode. Pull the
electrode vertically up suciently to grip the lead
between thumb and forenger.
Pull o the electrode, but keep hold of the lead. Fit
the new electrode to the lead. Fix the electrode in the
burner with screw. Replace the burner cap.
Check the burner ignition. Replace the pan supports.
2.5 To Replace a Hotplate Burner
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the hotplate tray (see 2.1). The burners (except
the right-hand wok burner) are mounted on support
struts. For these burners, disconnect the burner feed
pipes at the burner. Remove the screws at the front
and rear holding the support struts. Lift the strut and
burners clear. The burners are xed to the support struts
with 2 screws. Remove the appropriate burner and t
the new one.
Reassemble in reverse order. Check that the burner
operation is satisfactory.
Right-hand Wok Burner
Disconnect the burner feed pipes at the burner.
Fit the new one and reassemble in reverse order. Check
that the burner operation is satisfactory.
2.6 To Change a Hotplate Burner Thermocouple
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel and hotplate (see 1.1 & 2.1).
Unplug the FSD lead from the rear of the tap.
The thermocouple sits in a hole that has a slot at one
side. Ensure that the thermocouple is cool. Turn the
thermocouple so that the earth lead (no sleeve) is in line
with the slot. Lift the thermocouple clear of the hole.
Reassemble in reverse order.
… 33 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Falcon Toledo 90 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info