Bedienungsanleitung Fein wsb 14 125 t (Seite 16 von 99) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

391334

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

For your safety.

Read all safety warnings and all instruc-

tions. Failure to follow the warnings

and instructions may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this

Instruction Manual and the enclosed “General

Safety Instructions” (document number

3 41 30 054 06 1). The documents mentioned should be

kept for later use and enclosed with the power tool,

should it be passed on or sold.

Please also observe the relevant national industrial safety

regulations.

Safety Warnings common for Grinding, Sanding, Wire

Brushing or Abrasive Cutting Off Operations

This power tool is intended to function as a grinder, sander,

wire brush or cut-off tool. Read all safety warnings, instruc-

tions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or serious injury.

This power tool is not recommended for polishing. Opera-

tions for which the power tool was not designed may

create a hazard and cause personal injury.

Do not use accessories which are not specifically designed

and recommended by the tool manufacturer. Just because

the accessory can be attached to your power tool, it does

not assure safe operation.

The rated speed of the accessory must be at least equal to

the maximum speed marked on the power tool. Accessories

running faster than their rated speed can break and fly

apart.

The outside diameter and the thickness of your accessory

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately

guarded or controlled.

The arbor size of wheels, flanges, backing pads or any other

accessory must properly fit the spindle of the power tool.

Accessories with arbor holes that do not match the

mounting hardware of the power tool will run out of bal-

ance, vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and

cracks, backing pad for cracks, tear or excess wear, wire

brush for loose or cracked wires. If power tool or accessory

is dropped, inspect for damage or install an undamaged

accessory. After inspecting and installing an accessory,

position yourself and bystanders away from the plane of the

rotating accessory and run the power tool at maximum no-

load speed for one minute. Damaged accessories will nor-

mally break apart during this test time.

Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses. As

appropriate, wear dust mask, hearing protectors, gloves

and workshop apron capable of stopping small abrasive or

workpiece fragments. The eye protection must be capable

of stopping flying debris generated by various operations.

The dust mask or respirator must be capable of filtrating

particles generated by your operation. Prolonged expo-

sure to high intensity noise may cause hearing loss.

Keep bystanders a safe distance away from work area. Any-

one entering the work area must wear personal protective

equipment. Fragments of workpiece or of a broken acces-

sory may fly away and cause injury beyond immediate

area of operation.

Hold power tool by insulated gripping surfaces only, when

performing an operation where the cutting accessory may

contact hidden wiring or its own cord. Cutting accessory

contacting a “live” wire may make exposed metal parts of

the power tool “live” and shock the operator.

Position the cord clear of the spinning accessory. If you

lose control of the power tool, the cord may be cut or

snagged and your hand or arm may be pulled into the

spinning accessory.

Never lay the power tool down until the accessory has come

to a complete stop. The spinning accessory may grab the

surface and pull the power tool out of your control.

Character Unit of measure,

international

Unit of measure,

national

Explanation

n /min rpm Rated speed

W W Power input

W W Output

M… mm mm Size of metric thread

dB dB Sound power level

dB dB Sound pressure level

K… Uncertainty

m/s

Acceleration

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

/min, m/s

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

rpm, m/s

Basic and derived units of measure from the inter-

national system of units SI.

WARNING

3 41 01 104 06 0.book Seite 16 Mittwoch, 2. Juli 2008 1:43 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fein wsb 14 125 t Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info