Bedienungsanleitung Fein wsb 14 125 t (Seite 17 von 99) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

391334

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag

your clothing, pulling the accessory into your body.

Regularly clean the power tool’s air vents. The motor’s fan

will draw the dust inside the housing and excessive accu-

mulation of powdered metal may cause electrical haz-

ards.

Do not operate the power tool near flammable materials.

Sparks could ignite these materials.

Do not use accessories that require liquid coolants. Using

water or other liquid coolants may result in electrocution

or shock.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other acces-

sory. Pinching or snagging causes rapid stalling of the

rotating accessory which in turn causes the uncontrolled

power tool to be forced in the direction opposite of the

accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the mate-

rial causing the wheel to climb out or kick out. The wheel

may either jump toward or away from the operator,

depending on direction of the wheel’s movement at the

point of pinching. Abrasive wheels may also break under

these conditions.

Kickback is the result of power tool misuse and/or incor-

rect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

Maintain a firm grip on the power tool and position your

body and arm to allow you to resist kickback forces. Always

use auxiliary handle, if provided, for maximum control over

kickback or torque reaction during start-up. The operator

can control torque reactions or kickback forces, if proper

precautions are taken.

Never place your hand near the rotating accessory. Acces-

sory may kickback over your hand.

Do not position your body in the area where power tool will

move if kickback occurs. Kickback will propel the tool in

direction opposite to the wheel’s movement at the point

of snagging.

Use special care when working corners, sharp edges, etc.

Avoid bouncing and snagging the accessory. Corners,

sharp edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or kickback.

Do not attach a saw chain woodcarving blade or toothed

saw blade. Such blades create frequent kickback and loss

of control over the power tool.

Additional safety instructions for grinding and

cutting off operations

Use only wheel types that are recommended for your power

tool and the specific guard designed for the selected wheel.

Wheels for which the power tool was not designed can-

not be adequately guarded and are unsafe.

The guard must be securely attached to the power tool and

positioned for maximum safety, so the least amount of

wheel is exposed towards the operator. The guard helps to

protect operator from broken wheel fragments and acci-

dental contact with wheel.

Wheels must be used only for recommended applications.

For example: do not grind with the side of cut-off wheel.

Abrasive cut-off wheels are intended for peripheral

grinding, side forces applied to these wheels may cause

them to shatter.

Always use undamaged wheel flanges that are of correct

size and shape for your selected wheel. Proper wheel

flanges support the wheel thus reducing the possibility of

wheel breakage. Flanges for cut-off wheels may be differ-

ent from grinding wheel flanges.

Do not use worn down wheels from larger power tools.

Wheels intended for larger power tools are not suitable

for the higher speed of a smaller tool and may burst.

Additional safety warnings specific for abrasive

cutting off operations

Do not “jam” the cut-off wheel or apply excessive pressure.

Do not attempt to make an excessive depth of cut. Over-

stressing the wheel increases the loading and susceptibil-

ity to twisting or binding of the wheel in the cut and the

possibility of kickback or wheel breakage.

Do not position your body in line with and behind the rotat-

ing wheel. When the wheel, at the point of operation, is

moving away from your body, the possible kickback may

propel the spinning wheel and the power tool directly at

you.

When wheel is binding or when interrupting a cut for any

reason, switch off the power tool and hold the power tool

motionless until the wheel comes to a complete stop. Never

attempt to remove the cut-off wheel from the cut while the

wheel is in motion otherwise kickback may occur. Investi-

gate and take corrective action to eliminate the cause of

wheel binding.

Do not restart the cutting operation in the workpiece. Let

the wheel reach full speed and carefully reenter the cut.

The wheel may bind, walk up or kickback if the power

tool is restarted in the workpiece.

Support panels or any oversized workpiece to minimize the

risk of wheel pinching and kickback. Large workpieces

tend to sag under their own weight. Supports must be

placed under the workpiece near the line of cut and near

the edge of the workpiece on both sides of the wheel.

Use extra caution when making a “pocket cut” into existing

walls or other blind areas. The protruding wheel may cut

gas or water pipes, electrical wiring or objects that can

cause kickback.

Safety warnings specific for sanding operations

Do not use excessively oversized sanding disc paper. Follow

manufacturers recommendations, when selecting sanding

paper. Larger sanding paper extending beyond the sand-

ing pad presents a laceration hazard and may cause snag-

ging, tearing of the disc, or kickback.

3 41 01 104 06 0.book Seite 17 Mittwoch, 2. Juli 2008 1:43 13

Fein wsb 14 125 t Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info