Bedienungsanleitung Felisatti HF12.5 (Seite 5 von 24) (Deutsch, Englisch, Französisch, Spanisch)

502477

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5 - GB

Always turn off the switch and pull the power plug off rst

before mounting or dismounting the jacket.

3. Mounting / Dismounting the Side Handle (Optional)

(Fig.4)

The side handle of both HF12,5/1050 Hammers can be

mounted in two places. Select the one that is more conve-

nient for the work purpose and adjust the angle as necessary

(Can be rotated 360°).

Always turn off the switch and pull the power plug off rst

before mounting or dismounting the jacket.

4. Operating Method (Fig.5)

Place the end of the tool at the position for demolition and

operate the Hammer using its weight. Do not press too

hard. Too much pressure would not increase striking effect.

Always switch off and pull the power plug off when the work

is nished.

5. Adjustment and Fixing of Chisel Angle (Fig.6)

The chisel can be adjusted to 12 different position(in 30

increments). This ensures that at chisels and shaped chisels

can always be set to optimum working positions.

While pushing the selector forward as shown below, set

the desired angle in either clockwise or counterclockwise

direction and let go of the Selector.

Then the selector will be engaged with the body of the

Hammer preventing the rotation of the Chisel.

6. Operation time

The tools shall be operated intermittently as follows;

- Operating time : 30 s

- Resting time : 90 s

Supplementing and Relling the Grease (Fig.7)

1. About Relling the Grease

As this product is sealed tight, there will be no inltration of

dust or leakage of grease ensuring use of long period of time

without additional supply of grease.

Replacement of Grease

(1) Replacement of grease must be done at:

o Head Ofce of Felisatti

o Distributor of Felisatti Electric Machinery

o Felisatti authorized A/S Center

If it is inevitable to carry out replacement by yourself, follow

the instructions below:

Grease Replacement Method

(1) When replacement in crack case only is required:

Detach the Grease Cover and clean out the grease inside.

Rell 15g of Felisatti grease for Hammer (under 1/3 of a 50g

tube).

(2) When supplementing, use 10g (about 1/5 of a tube).

(3) When replacing the entire grease:

Remove all the grease and foreign matters from inside. Use

35g (about 2/3 of a tube) Replacement of entire grease must

be carried out by a Felisatti distributor or authorized A/S

center.

Close the Grease Cover rmly in place after supplementing

or relling the grease.

* Do not use too much grease. It may cause bad stroke.

* The grease supplied with this product is low viscosity

grease for Felisatti Hammer. Always use the grease of

the same.

* Grease can be purchased at a distributor or seller of

Felisatti Electric Machinery or at an authorized A/S

center.

Replacement of Carbon Brush (Fig.8,9)

When the carbon bruch reaches it end of life, the safety tip

inside will pop out preventing contact between Commutator

and carbon so that the Hammer can not be operated.

If this happens, both of the carbon brushes must be replaced

using the manufacture’s genuine carbon brush.

Detach the end cover by turning the screw using a + type

screwdriver.

Detach the brush cap using a - type screwdriver. Replace

the carbon brushes in both sides with new ones and lock

the brush cap.

Maintenance

1. Checking the Tool (bit)

Using the worn-off bit will cause overloading the motor and

reduce work efciency. Either sharpen the tool or replace with

a new one.

2. Checking the Screws

Check if any screw is losen. Losen screw must be fastened

rmly.

Replacement of screw must be carried out at the authorized

A/S center using genuine parts. Otherwise Commutator may

worn out quickly shortening the service life of the Tools.

3. Maintenance of Motor Assembly

The Commutator in the Motor Assembly is the core part of

the tool. Be careful not to cause scratch or contact with oil or

water on the surface of the Commutator

4. Storing after Use

Store the tool in a dry place out of reach of the children.

5. Repair

If the tool is not operating normally, do NOT attempt to locate

the problem or repair yourself. Contact nearest authorized

A/S center for service.

6. X attachment cord

If the supply cord of this power tool is damaged, it must be

replaced by a specially prepared cord available through the

service organization.

Do not dispose of electric tools

in the household waste!

In accordance with European Directive 2002/96/EC

relating to old electrical and electronic appliances

and its translation into national law, used electric

tools must be collected separately and recycled in

an ecologically desirable way.

DECLARATION OF

CONFORMITY

We hereby declare, under our sole

responsibility, that the FELISATTI

brand products described in this

manual comply with the following

standards or standard documents:

EN60745-1:2009+A11, EN60745-

2-6:2010, EN5014-1:2006+A1,

EN55014-2:1997+A1+A2, EN61000-

3-2:2006+A1+A2, EN61000-3-3:2008

in accordance with EU Directives

2006/42/EC, 2006/95/EC, 2004/108/

EC, 2002/95//EC, 2002/96/EC

Francisco Ruis

Technical director

We reserve the right to make technical changes 06/2011

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti HF12.5 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info